kuhse controller, German kuhse model, kuhse price

The kuhse controller is the component that directs the various parts of a computer to work in coordination according to the functional requirements of instructions. It is the neural center and command hub of the computer, composed of three components: the instruction register IR, the program counter PC, and the operation controller 0C. It is extremely important for coordinating the orderly operation of the entire computer. Each functional component within the CPU performs a specific function. The implementation of control components manages the transmission of information between components and the flow of data. The path for transmitting information between many digital components is commonly referred to as the "data path." Where the information starts, which register or multiplexer it passes through in the middle, and which register it finally reaches must all be controlled.

kuhse Controller Classification

Digital signals: Classified by voltage level, including 220VAC, 110VAC, and 24VDC; classified by isolation method, including relay isolation and transistor isolation. Analog signals: Classified by signal type, including current type (4-20mA, 0-20mA) and voltage type (0-10V, 0-5V, -10-10V); classified by precision, including 12bit, 14bit, and 16bit. In addition to the general IO mentioned above, there are special IO modules, such as RTD, thermocouple, and pulse modules. Module specifications and quantities are determined by the number of I/O points. The number of I/O modules can vary, but the maximum number is limited by the basic configuration management capability of the CPU, i.e., the maximum number of slots in the backplane or rack.

kuhse Controller Composition

1) Control memory (Control Memory) is used to store the microprograms corresponding to each machine instruction. The decoder is used to form the entry address for the microprogram corresponding to a machine instruction. When the microinstructions of the microprogram corresponding to a machine instruction are fetched one by one and sent to the microinstruction register, the micro-operation commands are issued according to the pre-designed sequence, thereby completing the function of that machine instruction. This applies to every machine instruction. 2) The width of the microinstruction directly determines the width of the microprogram controller. To simplify the control memory, measures can be taken to shorten the width of the microinstruction, such as adopting field decoding with single-stage segmented decoding. Obviously, the control field of the microinstruction will be significantly shortened. Some micro-operation commands that need to be generated simultaneously cannot be arranged in the same field. To further shorten the control field, field decoding can be designed as two-stage or multi-stage.

kuhse Controller Wiring

The controller power supply is 50 Hz, 220 V ± 10% AC. If a power failure occurs and the interruption time is less than 10 ms, the PLC operation is not affected. If the power interruption exceeds 10 ms or the voltage drop exceeds the allowable value, the PLC stops working, and all output points disconnect simultaneously. When power is restored, if the RUN input is connected, operation proceeds automatically. The PLC itself has sufficient resistance to interference from power lines. If power interference is particularly severe, an isolation transformer with a ratio of 1:1 can be installed to reduce interference between the equipment and ground. Good grounding is a necessary condition to ensure the reliable operation of the PLC and to avoid accidental voltage surge hazards. The grounding wire should be connected to the machine's grounding terminal, with the basic unit grounded. If an expansion unit is used, its grounding point should be connected to the grounding point of the basic unit. To suppress interference added to the power supply, input terminals, and output terminals, the programmable controller should be connected to a dedicated ground wire, and the grounding point should be separate from the grounding point of power equipment (such as motors). If this requirement cannot be met, common grounding with other equipment must be ensured, and series grounding with other equipment is prohibited. The grounding point should be as close as possible to the PLC.

Weidou Intelligent Technology professionally sells German kuhse servo drives, kuhse servo amplifiers, kuhse programmable controllers, kuhse control units, kuhse industrial PCs, kuhse logic controllers, kuhse drum controllers, kuhse relay controllers, kuhse control systems, kuhse motion controllers, kuhse microcontrollers, kuhse control modules, kuhse control switches, kuhse servo controllers, and kuhse expansion modules. kuhse products are original imports from Germany. Customers are welcome to inquire and order.