German THORMAS tools THORMAS models THORMAS prices

THORMAS tools refer to the general term for various metal devices manufactured through physical processing such as forging, rolling, and cutting of metals like iron, steel, and aluminum. Hardware tools, classified by product application, include: tool hardware, construction hardware, daily-use hardware, locks and abrasives, kitchen and bathroom hardware, home hardware, and hardware components. These include various manual, electric, pneumatic, and cutting tools; automotive maintenance tools; agricultural tools; lifting tools; measuring tools; tool machinery; cutting tools; jigs and fixtures; cutters; molds; cutting edges; grinding wheels; drill bits; polishing machines; tool accessories; measuring tools and cutters; painting tools; abrasives and grinding materials; manual socket wrench sockets; striking open-end wrenches and striking box-end wrenches.

THORMAS tool applications and usage

The electric hydraulic oil pump can serve as the hydraulic pump for various hydraulic equipment. When paired with other hydraulic tools, the electric hydraulic oil pump enables operations such as lifting, pressing, pipe bending, busbar bending, straightening, shearing, assembly, and disassembly. This reduces labor intensity and improves work efficiency. During use, open the air release nut, turn on the switch on the oil collection block, connect the power supply, and attach the quick coupler to the quick connector of the corresponding hydraulic equipment. Press the power switch; after the motor runs for 1-2 minutes, turn off the switch to engage the pressure boost state. At this point, the output hydraulic oil will perform various tasks, automatically increasing pressure with the load until 63MPA. After completing the work, open the switch to relieve pressure. Once the hydraulic oil has returned, remove the quick coupler, tighten the air release nut, unplug the power cord, and close the switch.

THORMAS tool usage

1) Rip cutting method: When sawing, place the wood on a bench, step on the wood with your right foot perpendicular to the saw line, stand straight with your left foot at an angle of 60° to the saw line, keep your right hand perpendicular to your right knee, and position your body at an angle of approximately 45° to the saw line. Lean forward slightly and move naturally, avoiding leaning left or lunging right. When sawing, hold the saw with your right hand and place your left thumb against the blade for positioning. Gently pull and push the saw a few times (pull first, then push) to start the kerf, then remove your left hand from the edge. When the teeth have cut into the wood about 5mm, use your left hand to assist your right hand in lifting and pushing the frame saw. Lift the saw lightly, raising the hand slightly; push the saw with more force, applying coordinated effort from the wrist, elbow, shoulder, and waist in a rhythmic manner. This ensures the saw blade follows the saw line. Otherwise, the edge of the rip-cut wood will be curved or uneven, or the kerf surface will be inconsistent. 2) Crosscutting method: When sawing, place the wood on a bench, stand to the left rear of the wood, hold the wood with your left hand, hold the saw with your right hand, and step on the wood with your left foot. The sawing method is the same as for rip cutting. When using a frame saw, the lower end of the blade should tilt forward. For rip sawing, the upper end of the blade tilts backward at an angle of approximately 75° to 90° (relative to the wood surface). For crosscutting, the blade tilts backward at an angle of approximately 30° to 45°. Always ensure the blade follows the line without deviation. Keep the kerf straight; do not allow the blade to wobble left or right, which causes skewing. When the wood is nearly severed, stabilize the cutoff piece with your left hand, slow down the sawing speed, and cut completely through. Do not leave any material to break off or snap by hand, as this can damage the blade and cause the wood to split along the grain, affecting quality.

THORMAS tool usage

1) Before use, carefully inspect the tool. Ensure there is no external damage, the switch operates flexibly without sticking, and the power cord and housing of the electric tool are intact. Use a 500V megohmmeter to measure the insulation resistance between the winding and the housing; it must not be less than O.5 megohms. See the attached table for insulation resistance values. 2) Handheld electric tools with metal housings must have a reliable protective grounding wire. The power cord should be a multi-core soft rubber-sheathed cable, with secure connections at both ends of the grounding protection wire. 3) Handheld electric tools should be used by dedicated personnel with appropriate professional knowledge. Strictly adhere to relevant safety operating procedures during use. 4) Before use, check that all related electrical and mechanical protective devices are intact and functioning normally. Also ensure that rotating parts move flexibly without sticking. 5) When using Class I handheld electric tools, operators must wear prescribed protective equipment and use qualified protective gear. Implement appropriate anti-electric shock safety measures as required, such as installing residual current devices (RCDs) in the power circuit, or having the operator wear insulating gloves, insulating shoes, or stand on an insulating mat. When using Class II handheld electric tools in damp, confined spaces, install a residual current circuit breaker (RCCB) with an operating current of less than 1.5mA and an operating time of less than or equal to 0.1 seconds. The RCCB should be placed inside the container and monitored by a dedicated person. 6) Occupational hazards of using handheld electric tools. Arm vibration disease caused by long-term exposure to hand-transmitted vibration was listed as one of China's statutory occupational diseases as early as 1957, also known as local vibration disease, typically manifesting as episodic white finger.

Weidou Intelligent Technology specializes in selling German THORMAS workholding fixtures, THORMAS hydraulic tools, THORMAS electric tools, THORMAS pneumatic tools, THORMAS manual tools, THORMAS electronic tools, THORMAS welding tools, THORMAS piping tools, THORMAS explosion-proof tools, THORMAS electrical power tools, THORMAS automotive maintenance tools, THORMAS fastening tools, THORMAS cutting tools, THORMAS striking tools, THORMAS grinding tools. THORMAS products are original imports from Germany. We welcome inquiries and orders from customers.