AKO Armaturen hose connectors Germany AKO Armaturen models AKO Armaturen prices

AKO Armaturen hose connectors are components used to connect water pipes. Connectors can be classified by usage method into: external thread termination water pipe connectors, compression ring water pipe connectors, and self-locking water pipe connectors. External thread termination water pipe connectors are die-cast from zinc alloy, with surfaces galvanized, sandblasted, or chrome-plated; they feature a compact structure, no pores, and high strength. Compression ring water pipe connectors can connect seamless steel pipes without threads to hoses, eliminating the threading process; simply screw in the nut. They feature a compact structure and high strength. Water pipe connectors can connect seamless steel pipes without threads or equipment cable outlet ports without threads to hoses, eliminating the threading process; they are die-cast from zinc alloy, with surfaces galvanized, sandblasted, or chrome-plated; they feature a compact structure and high strength. Widely used in high-end buildings, hotels, hospitals, office towers, stadiums, museums, government agencies, villas, and residential complexes.

AKO Armaturen hose connector installation

1. Cut the seamless steel pipe to the appropriate length and remove burrs from the pipe end. The pipe end face must be perpendicular to the axis, with an angular tolerance not greater than 0.5°. If the pipe needs to be bent, the straight section length from the pipe end to the bend must be at least three times the nut length. 2. Slide the nut and compression ring onto the seamless steel pipe. Pay attention to the direction of the nut and compression ring; do not install them backwards. 3. Apply lubricating oil to the threads of the pre-assembled connector body and the compression ring, insert the pipe into the connector body (the pipe must be fully inserted), and hand-tighten the nut. 4. Tighten the nut until the compression ring grips the pipe; this transition point can be felt by an increase in tightening torque (pressure point). 5. After reaching the pressure point, tighten the compression nut further by 1/2 turns. 6. Remove the pre-assembled connector body and check the embedding of the compression ring cutting edge; the visible raised band must fill the space at the compression ring end face. The compression ring may rotate slightly but must not move axially. 7. For final installation, apply lubricating oil to the threads of the connector body in the actual installation, mate it with the compression nut, and tighten until an increase in tightening torque is felt. Then tighten further by 1/2 turns to complete the installation.

AKO Armaturen hose connector selection

Unidirectional flow type: Rotary joints are installed at both ends of the drum; fluid enters from one end and exits from the other, without using an inner tube. Unidirectional flow type: A rotary joint is installed at one end of the drum, where fluid is both introduced and discharged; the inner tube remains stationary relative to the rotation of the drum. Bidirectional flow type (inner tube fixed): Different from the above, this type uses various siphon tubes inside the drum to discharge condensate; this type is mostly used for steam applications. Bidirectional flow type (inner tube rotating): This type is used in structures where the inner tube is fixed relative to the drum and rotates synchronously with it; in this case, fluid is introduced through the inner tube and discharged through the outer tube. Bidirectional flow type (inner tube rotating): A siphon device that rotates synchronously with the drum is installed inside the drum to discharge condensate; this type is mostly used for steam applications.

AKO Armaturen hose connector applications

Quick connectors are also commonly referred to as self-locking connectors or quick-insert sealing connectors. They allow locking of fittings and connectors through simple operation, without the need for nuts or clamps. They can withstand higher pressures, up to 70Bar or even higher. Flanged pipe openings or straight round pipes in cooling water channels typically require clamps for standard connectors, which involve more steps and have poorer pressure resistance. With technological advancements, in addition to self-locking quick connectors, pneumatic quick connectors (automation quick connectors) are better suited for industrial automated production, using pneumatic drive. The purpose of using quick connectors is to achieve faster operations; modern mechanized production emphasizes efficiency and reducing operator workload. Their speed is reflected in: easy handling, fewer operational steps, simple operation, automatic locking, and sealing/disconnection requiring only a single push-pull action, making them much more convenient than standard connectors.

Weidou Intelligent Technology specializes in selling German AKO Armaturen oil pipe connectors, AKO Armaturen hose connectors, AKO Armaturen pipe connectors, AKO Armaturen fitting connectors, AKO Armaturen rotary joints, AKO Armaturen metal connectors, AKO Armaturen brass connectors, AKO Armaturen stainless steel connectors, AKO Armaturen plastic connectors, AKO Armaturen hydraulic pipe connectors, AKO Armaturen adapter connectors, AKO Armaturen threaded pipe connectors, AKO Armaturen straight connectors, AKO Armaturen swivel connectors, AKO Armaturen compression ring connectors, AKO Armaturen original German imports. Welcome inquiries and orders from customers.