endress hauser electrical components, German endress hauser models, endress hauser prices

endress hauser electrical components are specifically designed to suppress high-frequency noise and spike interference on signal lines and power lines, and also have the ability to absorb electrostatic pulses. Ferrite beads are used to absorb ultra-high-frequency signals. Some RF circuits, PLL, oscillator circuits, and circuits containing ultra-high-frequency memory (DDR SDRAM, RAMBUS, etc.) all require ferrite beads at the power input. Inductors are energy storage components used in LC oscillator circuits, mid-to-low frequency filter circuits, etc., with an application frequency range rarely exceeding 50MHZ. Ferrite beads have high resistivity and permeability, equivalent to a resistor and inductor in series, but both resistance and inductance vary with frequency.

endress hauser electrical component principles

The thermistor will remain in a non-tripped state for a long time; when the ambient temperature and current are in the c region, the heat dissipation power of the thermistor is close to its heat generation power, so it may or may not trip. For a thermistor at the same ambient temperature, the tripping time decreases sharply as the current increases; at relatively higher ambient temperatures, the thermistor has a shorter tripping time and lower holding and tripping currents. The PTC effect refers to a material having a PTC effect, i.e., a positive temperature coefficient effect, meaning only that the material's resistance increases with rising temperature. For example, most metal materials exhibit the PTC effect. In these materials, the PTC effect manifests as a linear increase in resistance with temperature, which is commonly referred to as the linear PTC effect. Non-linear PTC effect: Materials undergoing phase transitions exhibit a phenomenon where resistance increases abruptly by several to more than ten orders of magnitude over a narrow temperature range, known as the non-linear PTC effect. Many types of conductive polymers exhibit this effect, such as polymer PTC thermistors. These conductive polymers are very useful for manufacturing overcurrent protection devices. Polymer PTC thermistors are used for overcurrent protection and are often called self-resetting fuses (hereinafter referred to as thermistors). Due to their unique positive temperature coefficient resistance characteristics, they are highly suitable as overcurrent protection devices. Thermistors are used in series in circuits, similar to standard fuses. When the circuit operates normally, the thermistor temperature is close to room temperature, and its resistance is very low, so it does not hinder current flow when connected in series. However, when an overcurrent occurs due to a fault, the thermistor's temperature rises due to increased heat generation. When the temperature exceeds the switching temperature, the resistance increases sharply, and the current in the circuit rapidly drops to a safe value. After the thermistor trips, the current in the circuit is significantly reduced. t is the tripping time of the thermistor. Due to the good design flexibility of polymer PTC thermistors, their temperature sensitivity can be adjusted by changing their switching temperature (ts), allowing them to provide both over-temperature and overcurrent protection. They are suitable for overcurrent and over-temperature protection of lithium-ion and nickel-metal hydride batteries. Influence of ambient temperature on polymer PTC thermistors: Polymer PTC thermistors are direct-heated, step-type thermistors. Their resistance change process is related to their own heat generation and dissipation, so their holding current, tripping current, and tripping time are affected by ambient temperature.

endress hauser electrical component characteristics

Sensitivity refers to the ratio of the change in output to the change in input of a sensor under steady-state operating conditions. It is the slope of the output-input characteristic curve. If the relationship between the sensor's output and input is linear, then the sensitivity S is a constant. Otherwise, it will vary with changes in the input. The dimension of sensitivity is the ratio of the dimensions of the output and input quantities. When the dimensions of the sensor's output and input are the same, sensitivity can be understood as the amplification factor. Increasing sensitivity yields higher measurement accuracy. However, the higher the sensitivity, the narrower the measurement range, and often the poorer the stability.

endress hauser electrical component types

Inductors can be made by winding conductive material, typically copper wire, around a magnetic core, or the core can be removed or replaced with ferromagnetic material. Core materials with higher permeability than air can confine the magnetic field more tightly around the inductor component, thereby increasing inductance. There are many types of inductors; most are made with enamel-coated coils wound around ferrite bobbins, while some shielded inductors place the coil entirely within the ferrite. The cores of some inductor components are adjustable, allowing the inductance value to be changed. Small inductors can be directly etched onto PCB boards using a spiral trace method. Small-value inductors can also be manufactured in integrated circuits using the same processes as transistors. In these applications, aluminum interconnects are often used as the conductive material. Regardless of the method, due to practical constraints, the most commonly used approach is a circuit called a "gyrator," which uses a capacitor and active components to exhibit the same characteristics as an inductor. Inductor components used for blocking high frequencies are often constructed from a metal wire passing through a magnetic pillar or ferrite bead.

Weidou Intelligent Technology specializes in selling German endress hauser connectors, endress hauser switches, endress hauser relays, endress hauser controllers, endress hauser plugs, endress hauser sensors, endress hauser resistors, endress hauser capacitors, endress hauser buses, endress hauser modules, endress hauser cables, endress hauser power supplies, endress hauser interfaces, endress hauser gateways, endress hauser circuit breakers. endress hauser products are original imports from Germany. Customers are welcome to inquire and order.