Siebert electrical components Germany Siebert model Siebert price

Siebert electrical component is a high-power electrical component, also known as a thyristor. It has the advantages of small size, high efficiency, and long service life. In automatic control systems, it can serve as a high-power drive device, enabling low-power control elements to control high-power equipment. It is widely used in AC/DC motor speed control systems, power regulation systems, and servo systems. Thyristors are divided into unidirectional thyristors and bidirectional thyristors. Bidirectional thyristors are also called triac bidirectional thyristors, abbreviated as TRIAC. Structurally, a bidirectional thyristor is equivalent to two unidirectional thyristors connected in reverse; this type of thyristor has bidirectional conduction capability. Its on/off state is determined by the control electrode G. Applying a positive pulse (or negative pulse) to the control electrode G enables forward (or reverse) conduction. The advantages of this device include a simple control circuit and no reverse voltage withstand issue, making it particularly suitable for use as an AC contactless switch.

Siebert electrical component usage

1, apply moderate force when tightening terminal connections to prevent stripping the threads of bolts and nuts due to excessive force. Replace any stripped bolts and nuts promptly; do not continue operation with compromised fasteners. 2, when using a screwdriver to tighten or loosen screws, ensure the screwdriver tip is firmly seated in the screw head before applying torque to prevent slippage that could damage the screw and make disassembly difficult, especially for common miniature circuit breakers inside distribution boxes. 3, if bolts or nuts are difficult to remove, do not act rashly to avoid deformation that would make removal even harder. Apply gentle tapping or use a screw loosening agent or dilute hydrochloric acid, then attempt removal after a short wait. 4, do not use pliers to tighten or loosen bolts or nuts to prevent damage. When using an adjustable wrench, adjust the jaw opening properly to avoid damaging or deforming the bolt or nut, which could hinder disassembly. 5, a single terminal block allows connection of at most two wires of the same type and specification. 6, for terminal blocks prone to loosening or poor contact, wire ends must be secured in a "?" shape around the terminal to increase contact area and prevent loosening. 7, when connecting wire joints or cable lugs to each other, do not insert non-copper washers or washers with poor conductivity between them. 8, when connecting wire joints, ensure the contact surfaces are smooth and free of oxidation. When connecting cable lugs or copper busbars, clean the contact surfaces, apply conductive paste, and then tighten. 9, when connecting temporary wiring, fold flexible single-conductor wire ends once before connecting to the lower terminal of the miniature circuit breaker; solid single-core wires must be connected to the lower terminal of the miniature circuit breaker in a "?" shape. 10, for high-voltage motor wiring, do not insert washers with poor conductivity (such as galvanized nuts, flat washers, or spring washers) between the motor output leads and the cables connecting to the motor. 14, when wrapping cables or other equipment requiring insulation protection with insulating tape, wrap the insulation layer from one end to the other with sufficient overlap, ensuring at least one full back-and-forth pass.

Siebert electrical component principle

The basic principle of a multimeter uses a sensitive moving-coil DC ammeter (microammeter) as the meter movement. When a small current passes through the meter movement, it produces a current indication. However, the meter movement cannot handle large currents, so resistors must be connected in parallel and series to shunt or drop voltage, thereby measuring current, voltage, and resistance in the circuit. In digital multimeters, the measurement process involves a conversion circuit that converts the measured quantity into a DC voltage signal. An analog-to-digital (A/D) converter then transforms the analog voltage into a digital value, which is counted by an electronic counter, and the result is displayed directly as numbers on the screen. The voltage, current, and resistance measurement functions of a multimeter are implemented through the conversion circuit. Current and resistance measurements are based on voltage measurement, meaning digital multimeters are extended from digital DC voltmeters. The A/D converter in a digital DC voltmeter converts continuously varying analog voltage over time into digital values. An electronic counter counts these digital values to obtain the measurement result, which is then shown by the decoding display circuit. Logic control circuits coordinate the operation, completing the entire measurement process sequentially under the action of a clock signal.

Siebert electrical component classification

Based on the working power supply, electric motors are classified into DC motors and AC motors. AC motors are further divided into single-phase motors and three-phase motors. By structure and operating principle, motors are classified into DC motors, asynchronous motors, and synchronous motors. Synchronous motors include permanent magnet synchronous motors, reluctance synchronous motors, and hysteresis synchronous motors. Asynchronous motors are divided into induction motors and AC commutator motors. Induction motors include three-phase asynchronous motors, single-phase asynchronous motors, and shaded-pole asynchronous motors. AC commutator motors include single-phase series-wound motors, AC/DC universal motors, and repulsion motors. By starting and running method, motors are classified into capacitor-start single-phase asynchronous motors, capacitor-run single-phase asynchronous motors, capacitor-start-run single-phase asynchronous motors, and split-phase single-phase asynchronous motors. By application, motors are divided into drive motors and control motors. Drive motors include those for power tools, home appliances, and other general small mechanical equipment. Control motors include stepper motors and servo motors. By rotor structure, motors are classified into squirrel-cage induction motors and wound-rotor induction motors. By operating speed, motors are classified into high-speed motors, low-speed motors, constant-speed motors, and variable-speed motors.

Weidou Intelligent Technology specializes in selling German Siebert connectors, Siebert switches, Siebert relays, Siebert controllers, Siebert plugs, Siebert sensors, Siebert resistors, Siebert capacitors, Siebert buses, Siebert modules, Siebert cables, Siebert power supplies, Siebert interfaces, Siebert gateways, Siebert circuit breakers, Siebert original imports from Germany. Customers are welcome to inquire and place orders.