Bosch Rexroth R901200381 Part No. R901200381 Clamping and Drive Module Distribution

R901200381 Bosch Rexroth UPE2 Clamping and Drive Module (51142) IH15A Control modules are used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control modules can be connected directly to the clamping and drive module UPE2. However, with the aid of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be mounted directly on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units for small-volume consumers with a volume flow not exceeding 602 l/min. They are connected to each other by two tie rods. Clamping and drive module

R901200381 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not possible. – For more details, see the brochure "Control block types for clamping and drive modules IH15A". 2) Directional valve module "W" 1): – Design that allows control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – The control is designed according to the respective application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control block types for clamping and drive modules IH204A". Directional valve modules and seat valve modules can be combined!

R901200381 Notes on commissioning clamping and drive modules

When designing controllers with tanks, ensure that type-tested relief valves protect the tank from impermissible overpressure. Type-tested relief valves must not perform any control tasks, and the set pressure of the type-tested relief valve must be less than or equal to the maximum permissible working pressure of the tank. 9 xp (minimum working pressure) when using modules SPDB and SPDR, a filter with a filtration rating of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. The length dimensions are calculated by adding the dimensions "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). For example: IH15BA006-1X / 07024AA / W220N9K4M01 Nominal size A IH15B assembly max. 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, version AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforms to ISO 228 Part 1. Filter element assembly tool: - With pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the filter cartridge upwards to the stop on the stop. Then rotate the filter cartridge approx. 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the filter cartridge as far as possible. Then turn back approx. 1/8 to 1/1191 turns.

R901200381 Motors for clamping and drive modules

Clamping and drive modules are designed for short-time operation S2 and intermittent operation S3 duty cycles within the nominal power range, in accordance with standard VDE 0530 (EN 60034). The motors comply with insulation class F, and the entire clamping and drive module complies with protection class IP 54. The direction of rotation of the motor depends on the installed pump (for this, see "Technical Data" on page 4). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Duty cycle S2 short-time operation, S3 intermittent operation. Insulation class F (winding). Protection class IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG), according to the provisions of the EEC directive "Act on the Electromagnetic Compatibility of Equipment (Chapter 2 Section 4)", the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik of 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-249 Hz. Terminal assignment, terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in selling Bosch Rexroth R901200381 Part No. R901200381 clamping and drive modules, R901200381 control modules, R901200381 drive modules, R901200381 clamping modules, R901200381 Bosch Rexroth modules, UPE2388 clamping and drive modules, R901200381 compact modules, R901200381 motor modules, R901200381 hydraulic modules, R901200381 directional valve modules, R901200381 seat valve modules, IH2401MA modules, IH2401EA modules, R901200381 indexing modules, R901200381 release modules, R901200381 original German imports. Welcome inquiries and orders from users.