Bosch Rexroth R900710237 Part No. R900710237 Clamping and Drive Module Distribution

R900710237 Bosch Rexroth UPE2 Clamping and Drive Module (51142) The IH15A control module is used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control module can be directly connected to the clamping and drive module UPE2. However, with the help of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be directly mounted on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units for small-volume consumers with a volume flow not exceeding 484 l/min. They are connected to each other by two tie rods. Clamping and drive module

R900710237 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design that allows control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH86A". Directional valve modules and seat valve modules can be combined!

R900710237 Notes on Commissioning Clamping and Drive Modules

When designing controllers with tanks, ensure that type-tested relief valves protect the tank from impermissible overpressure. Type-tested relief valves must not assume any control tasks, and the set pressure of the type-tested relief valve must be less than or equal to the maximum allowable working pressure of the tank. 9 xp (minimum working pressure) When using modules SPDB and SPDR, a filter with a filtration fineness of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. The length dimension is calculated by adding the dimensions "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). For example: IH15BA006-1X / 07024AA / W220N9K4M01 Nominal size A of the IH15B assembly up to 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, variant AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforms to ISO 228 Part 1. Cartridge assembly tool: - With pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the cartridge upwards to the stop on the stop. Then rotate the cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the cartridge as far as possible. Then turn back approximately 1/8 to 1/1073 turns.

R900710237 Motors for Clamping and Drive Modules

Clamping and drive modules are designed for short-time operation S2 and intermittent operation S3 duty cycles within the nominal power range, in accordance with standard VDE 0530 (EN 60034). The motor complies with insulation class F, and the entire clamping and drive module complies with protection rating IP 54. The direction of rotation of the motor depends on the installed pump (for this, refer to "Technical Data" on page 4). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Duty cycle S2 short-time operation, S3 intermittent operation. Insulation class F (winding). Protection rating IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the provisions of the EEC directive "Act on Electromagnetic Compatibility of Equipment (Chapter 2, Section 4)", the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik of 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-131 Hz. Terminal assignment, terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in selling Bosch Rexroth R900710237 Part No. R900710237 Clamping and Drive Modules, R900710237 Control Modules, R900710237 Drive Modules, R900710237 Clamping Modules, R900710237 Bosch Rexroth Modules, UPE2270 Clamping and Drive Modules, R900710237 Compact Modules, R900710237 Motor Modules, R900710237 Hydraulic Modules, R900710237 Directional Valve Modules, R900710237 Seat Valve Modules, IH2283MA Modules, IH2283EA Modules, R900710237 Indexing Modules, R900710237 Release Modules, R900710237 Original German Import. Welcome inquiries and orders from users.