Bosch Rexroth R900259587 Part No. R900259587 Clamping and Drive Module Distribution

R900259587 Bosch Rexroth UPE2 clamping and drive module (51142) IH15A control modules are used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control modules can be connected directly to the clamping and drive module UPE2. However, with the aid of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be mounted directly on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units for small-volume consumers with a volumetric flow rate not exceeding 409 l/min. They are interconnected by two tie rods. Clamping and drive module

R900259587 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design that allows control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of a seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the respective application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH111A". Directional valve modules and seat valve modules can be combined!

R900259587 Technical Data for Clamping and Drive Modules

When designing controllers with tanks, ensure that the tank is protected against impermissible overpressure by a type-tested relief valve. Type-tested relief valves must not perform any control tasks, and the set pressure of the type-tested relief valve must be less than or equal to the maximum allowable working pressure of the tank. When using modules SPDB and SPDR at 9 xp (minimum working pressure), a filter with a filtration rating of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. The length dimensions are calculated by adding the dimensions "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). For example: IH15BA006-1X / 07024AA / W220N9K4M01 IH15B assembly with nominal size A up to 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, version AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforming to ISO 228 part 1. Cartridge assembly tool: - With pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the cartridge upward to the stop on the stop. Then rotate the cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the cartridge as far as possible. Then turn back approximately 1/8 to 1/998 turns.

R900259587 Air Breathers and Oil Trays for Clamping and Drive Modules

Air breather (option): We recommend using an air breather when operating clamping and drive modules in heavily contaminated environments. During installation, the connection between the air breather and the engine intake pipe, whether via flange, rubber hose, or direct connection, must be tight and reliable to prevent air leaks. Rubber gaskets must be installed on both end faces of the filter element. The wing nuts securing the air breather housing must not be tightened excessively to avoid crushing the paper filter element. During use, strictly prevent the paper core air breather from getting wet with rain, as significant moisture absorption by the paper core will greatly increase intake resistance and shorten service life. Furthermore, paper core air breathers must not come into contact with oil or fire. Oil tray (option) (dimensions in mm): Size 3 and size 4 Material No. R901109231, size 5 and size 7 Material No. R901109235, Color: RAL 7131 "Light Gray."

Weidou Intelligent Technology specializes in selling Bosch Rexroth R900259587 Part No. R900259587 clamping and drive modules, R900259587 control modules, R900259587 drive modules, R900259587 clamping modules, R900259587 Bosch Rexroth modules, UPE2195 clamping and drive modules, R900259587 compact modules, R900259587 motor modules, R900259587 hydraulic modules, R900259587 directional valve modules, R900259587 seat valve modules, IH2208MA modules, IH2208EA modules, R900259587 indexing modules, R900259587 release modules, R900259587 original German imports. Customers are welcome to inquire and order.