Bosch Rexroth IH15MA-1X/WZ-V-005 Part No. R904100524 Clamping and Drive Module Distribution

R904100524 Bosch Rexroth UPE2 Clamping and Drive Module (51142) IH15A Control modules are used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control modules can be connected directly to the clamping and drive module UPE2. However, with the aid of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be mounted directly on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units for small-volume consumers with a volume flow not exceeding 385 l/min. They are connected to each other by two tie rods. Clamping and drive module

R904100524 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding pressure functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design that allows control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – The control is designed according to the respective application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH87A". Directional valve modules and seat valve modules can be combined!

R904100524 Technical Data for Clamping and Drive Modules

When designing controllers with tanks, ensure that the tank is protected against impermissible overpressure by a type-tested pressure relief valve. Type-tested pressure relief valves must not perform any control tasks, and the set pressure of the type-tested pressure relief valve must be less than or equal to the maximum permissible working pressure of the tank. When using modules SPDB and SPDR at 9 xp (minimum working pressure), a filter with a filtration rating of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. The length dimensions are calculated by adding the dimensions "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). Example: IH15BA006-1X / 07024AA / W220N9K4M01 Nominal size A IH15B assembly up to 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, variant AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforms to ISO 228 Part 1. Filter element assembly tool: - With pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the filter cartridge upward to the stop on the stop. Then rotate the filter cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the filter cartridge as far as possible. Then turn back approximately 1/8 to 1/974 turns.

R904100524 Air Filters and Oil Trays for Clamping and Drive Modules

Air filter (option): We recommend using an air filter when operating clamping and drive modules in heavily contaminated environments. During installation, the connection between the air filter and the engine intake pipe, whether via flange, rubber hose, or direct connection, must be tight and reliable to prevent air leaks. Rubber gaskets must be installed on both end faces of the filter element. The wing nuts securing the air filter housing must not be overtightened to avoid crushing the paper filter element. During use, strictly prevent the paper core air filter from getting wet with rain, as absorbing a large amount of water will significantly increase intake resistance and shorten service life. In addition, paper core air filters must not come into contact with oil or fire. Oil tray (option) (dimensions in mm): Size 3 and size 4 Material No. R901109231, size 5 and size 7 Material No. R901109235, Color: RAL 7107 "Light gray."

Weidou Intelligent Technology specializes in the sales of Bosch Rexroth IH15MA-1X/WZ-V-005 Part No. R904100524 Clamping and Drive Modules, R904100524 Control Modules, R904100524 Drive Modules, R904100524 Clamping Modules, R904100524 Bosch Rexroth Modules, UPE2171 Clamping and Drive Modules, R904100524 Compact Modules, R904100524 Motor Modules, R904100524 Hydraulic Modules, R904100524 Directional Valve Modules, R904100524 Seat Valve Modules, IH2184MA Modules, IH2184EA Modules, R904100524 Indexing Modules, R904100524 Release Modules, R904100524 Original German imports. Welcome inquiries and orders from users.