Bosch Rexroth IH15MA-1X/WSED-2HED5/100/D100/V Part No. R904100319 Clamping and Drive Module Distribution

R904100319 Bosch Rexroth UPE2 Clamping and Drive Module (51142) The IH15A control module is used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control module can be directly connected to the clamping and drive module UPE2. However, with the help of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be directly mounted on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units of small-volume consumers with a volumetric flow rate not exceeding 368 l/min. They are interconnected by two tie rods. Clamping and drive module

R904100319 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design that allows control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the respective application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH70A". Directional valve modules and seat valve modules can be combined!

R904100319 Technical Data for Clamping and Drive Modules

When designing controllers with tanks, ensure that type-tested pressure relief valves protect the tank from impermissible overpressure. Type-tested pressure relief valves must not perform any control tasks, and the set pressure of the type-tested pressure relief valve must be less than or equal to the maximum allowable working pressure of the tank. When using modules SPDB and SPDR at 9 xp (minimum working pressure), a filter with a filtration rating of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. The length dimensions are calculated by adding the dimensions "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). For example: IH15BA006-1X / 07024AA / W220N9K4M01 Nominal size A IH15B assembly up to 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, variant AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforms to ISO 228 Part 1. Filter element assembly tool: - With pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the filter cartridge upward to the stop on the stop. Then rotate the filter cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the filter cartridge as far as possible. Then turn back approximately 1/8 to 1/957 turns.

R904100319 Air Filters and Oil Trays for Clamping and Drive Modules

Air filter (option): We recommend using an air filter when using clamping and drive modules in heavily contaminated environments. During installation, whether flanged, connected via rubber hose, or directly connected between the air filter and the engine intake pipe, the connection must be tight and reliable to prevent air leakage. Rubber gaskets must be installed on both end faces of the filter element; the wing nuts securing the air filter outer cover must not be tightened too tightly to avoid crushing the paper filter element. During use, strictly prevent the paper core air filter from getting wet by rain, as once the paper core absorbs a large amount of moisture, it will greatly increase the intake resistance and shorten service life. In addition, paper core air filters must not come into contact with oil or fire. Oil tray (option) (dimensions in mm): Size 3 and size 4 Material No. R901109231, size 5 and size 7 Material No. R901109235, Color: RAL 7090 "Light gray."

Weidou Intelligent Technology specializes in selling Bosch Rexroth IH15MA-1X/WSED-2HED5/100/D100/V Part No. R904100319 Clamping and Drive Modules, R904100319 Control Modules, R904100319 Drive Modules, R904100319 Clamping Modules, R904100319 Bosch Rexroth Modules, UPE2154 Clamping and Drive Modules, R904100319 Compact Modules, R904100319 Motor Modules, R904100319 Hydraulic Modules, R904100319 Directional Valve Modules, R904100319 Seat Valve Modules, IH2167MA Modules, IH2167EA Modules, R904100319 Indexing Modules, R904100319 Release Modules, R904100319 Original German Import. Welcome customers to inquire and order.