Bosch Rexroth IH15MA-1X/WSED-1HED8/100/D/V-001 Part No. R900335956 Clamping and Drive Module Distribution

R900335956 Bosch Rexroth UPE2 clamping and drive module (51142) IH15A control modules are used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control modules can be directly connected to the clamping and drive module UPE2. However, with the aid of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be directly mounted on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units for small-volume consumers with a volume flow not exceeding 349 l/min. They are interconnected by two tie rods. Clamping and drive module

R900335956 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design allowing control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of a seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH51A". Directional valve modules and seat valve modules can be combined!

R900335956 Technical Data for Clamping and Drive Modules

When designing controllers with tanks, ensure that type-tested pressure relief valves protect the tank from impermissible overpressure. Type-tested pressure relief valves must not perform any control tasks, and the set pressure of the type-tested pressure relief valve must be less than or equal to the maximum allowable working pressure of the tank. When using modules SPDB and SPDR at 9 xp (minimum working pressure), a filter with a filtration rating of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. The length dimensions are calculated by adding the dimension "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). Example: IH15BA006-1X / 07024AA / W220N9K4M01 IH15B assembly, nominal size A, max. 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, version AA, 220 V AC voltage, N9 manual operation, K4 connection type, seal material Perbunan, connection type with pipe thread conforming to ISO 228 part 1. Cartridge assembly tool: - with pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the cartridge upward against the stop on the stop. Then rotate the cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the cartridge as far as possible. Then turn back approximately 1/8 to 1/938 turns.

R900335956 Air Filters and Oil Trays for Clamping and Drive Modules

Air filter (option): We recommend using an air filter when operating clamping and drive modules in heavily contaminated environments. During installation, the connection between the air filter and the engine intake pipe, whether via flange, rubber hose, or direct connection, must be tight and reliable to prevent air leaks. Rubber gaskets must be installed on both end faces of the filter element. The wing nuts securing the air filter housing must not be overtightened to avoid crushing the paper filter element. During use, strictly prevent the paper core air filter from getting wet with rain, as absorbing a large amount of water will significantly increase intake resistance and shorten service life. In addition, paper core air filters must not come into contact with oil or fire. Oil tray (option) (dimensions in mm): Size 3 and size 4 Material No. R901109231, size 5 and size 7 Material No. R901109235, Color: RAL 7071 "Light Gray.

Weidou Intelligent Technology specializes in selling Bosch Rexroth IH15MA-1X/WSED-1HED8/100/D/V-001 Part No. R900335956 clamping and drive modules, R900335956 control modules, R900335956 drive modules, R900335956 clamping modules, R900335956 Bosch Rexroth modules, UPE2135 clamping and drive modules, R900335956 compact modules, R900335956 motor modules, R900335956 hydraulic modules, R900335956 directional valve modules, R900335956 seat valve modules, IH2148MA modules, IH2148EA modules, R900335956 indexing modules, R900335956 release modules, R900335956 original German imports. Welcome inquiries and orders from users.