Bosch Rexroth IH15MA-1X/SD-2HED8/100/O/V Part No. R904101618 Clamping and Drive Module Distribution

R904101618 Bosch Rexroth UPE2 Clamping and Drive Module (51142) IH15A Control modules are used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and control modules can be connected directly to the clamping and drive module UPE2. However, with the aid of external accessory modules, hydraulic control units can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be mounted directly on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control of small-volume consumers with a volume flow not exceeding 318 l/min. They are interconnected by two tie rods. Clamping and drive module

R904101618 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding pressure functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design allowing control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of a seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH20A". Directional valve modules and seat valve modules can be combined!

R904101618 Technical Data for Clamping and Drive Modules

When designing controllers with tanks, ensure that type-tested relief valves protect the tank from impermissible overpressure. Type-tested relief valves must not perform any control tasks, and the set pressure of the type-tested relief valve must be less than or equal to the maximum allowable working pressure of the tank. When using modules SPDB and SPDR at 9 xp (minimum working pressure), a filter with a filtration fineness of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. Length dimensions are calculated by summing the "X" dimensions of the directional valve modules (see pages 19 to 21) and poppet valve modules (see pages 31 to 72). Example: IH15BA006-1X / 07024AA / W220N9K4M01 Nominal size A IH15B assembly up to 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, variant AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforms to ISO 228 Part 1. Filter element assembly tool: - With pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the filter cartridge upward to the stop on the stop. Then rotate the filter cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the filter cartridge as far as possible. Then turn back approximately 1/8 to 1/907 turns.

R904101618 Air Filters and Oil Trays for Clamping and Drive Modules

Air filter (option): We recommend using an air filter when operating clamping and drive modules in heavily contaminated environments. During installation, whether using a flange, rubber hose connection, or direct connection between the air filter and the engine intake pipe, the connection must be tight and reliable to prevent air leaks. Rubber gaskets must be installed on both end faces of the filter element. The wing nuts securing the air filter outer cover must not be overtightened to avoid crushing the paper filter element. During use, strictly prevent the paper core air filter from getting wet with rain, as absorbing a large amount of water will significantly increase intake resistance and shorten service life. In addition, paper core air filters must not come into contact with oil or fire. Oil tray (option) (dimensions in mm): Size 3 and size 4 Material No. R901109231, size 5 and size 7 Material No. R901109235, Color: RAL 7040 "Light gray."

Weidou Intelligent Technology specializes in the sales of Bosch Rexroth IH15MA-1X/SD-2HED8/100/O/V Part No. R904101618 Clamping and Drive Modules, R904101618 Control Modules, R904101618 Drive Modules, R904101618 Clamping Modules, R904101618 Bosch Rexroth Modules, UPE2104 Clamping and Drive Modules, R904101618 Compact Modules, R904101618 Motor Modules, R904101618 Hydraulic Modules, R904101618 Directional Valve Modules, R904101618 Seat Valve Modules, IH2117MA Modules, IH2117EA Modules, R904101618 Indexing Modules, R904101618 Release Modules, R904101618 Original German Import. Welcome inquiries and orders from users.