Bosch Rexroth IH15EA-1X/SSB-S210E/O/0, 75/V Part No. R900703590 Clamping and Drive Module Distribution

R900703590 Bosch Rexroth UPE2 The IH15A control module for the clamping and drive module (51142) is used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control module can be directly connected to the clamping and drive module UPE2. However, with the help of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be directly mounted on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units of small volume consumers with a volumetric flow rate not exceeding 163 l/min. They are connected to each other by two tie rods. Clamping and drive module

R900703590 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design that allows control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH164A". Directional valve modules and seat valve modules can be combined!

R900703590 Features and Applications of Clamping and Drive Modules

When designing controllers with tanks, ensure that type-tested pressure relief valves protect the tank from impermissible overpressure. Type-tested pressure relief valves must not perform any control tasks, and the set pressure of the type-tested pressure relief valve must be less than or equal to the maximum allowable working pressure of the tank. When using modules SPDB and SPDR at 9 xp (minimum working pressure), a filter with a filtration fineness of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. The length dimension is calculated by adding the dimensions "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). For example: IH15BA006-1X / 07024AA / W220N9K4M01 Nominal size A IH15B assembly up to 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, variant AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforms to ISO 228 Part 1. Cartridge assembly tool: - With pipe wrench Material No.: R904001048. Installation instructions for F30: - Turn the cartridge upwards to the stop on the stop. Then rotate the cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the cartridge as far as possible. Then turn back approximately 1/8 to 1/752 turns.

R900703590 Motors for Clamping and Drive Modules

Clamping and drive modules are designed for short-time operation S2 and intermittent operation S3 modes within the nominal power range, in accordance with standard VDE 0530 (EN 60034). The motor complies with insulation class F, and the entire clamping and drive module complies with protection class IP 54. The direction of rotation of the motor depends on the installed pump (for this, see "Technical Data" on page 4). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time operation, S3 intermittent operation. Insulation class F (winding). Protection class IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG), according to the provisions of the "Act on Electromagnetic Compatibility of Equipment (Chapter 2 Section 4)" under the EEC directive, the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components produced by Murr-Elektronik company in 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-209 Hz. Terminal assignment, terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in selling Bosch Rexroth IH15EA-1X/SSB-S210E/O/0, 75/V Part No. R900703590 Clamping and Drive Modules, R900703590 Control Modules, R900703590 Drive Modules, R900703590 Clamping Modules, R900703590 Bosch Rexroth Modules, UPE1949 Clamping and Drive Modules, R900703590 Compact Modules, R900703590 Motor Modules, R900703590 Hydraulic Modules, R900703590 Directional Valve Modules, R900703590 Seat Valve Modules, IH1962MA Modules, IH1962EA Modules, R900703590 Indexing Modules, R900703590 Release Modules, R900703590 Original German Import, welcome customers to inquire and order.