Bosch Rexroth IH15EA-1X/GDH-S350/MNHED8G24V Part No. R904100599 Clamping and Drive Module Distribution

R904100599 Bosch Rexroth UPE 2 The clamping and drive module constitutes a complete drive system that is ready for connection upon delivery. It is used to supply hydraulic oil to the hydraulic circuit. Due to thermal load considerations, the clamping and drive module operates in short-time and intermittent duty modes. The duty cycle is selected based on power output and environmental conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module operates in a vertical installation position. Optionally, the UPE 124 clamping and drive module can be equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R904100599 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding pressure functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control block types for clamping and drive modules. IH15A". 2) Directional valve module "W" 1): – Allows control designs using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of a seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH137A". Directional valve modules and seat valve modules can be combined!

R904100599 Technical data for clamping and drive modules

When designing controllers with tanks, ensure that type-tested relief valves protect the tank from impermissible overpressure. Type-tested relief valves must not perform any control tasks, and the set pressure of the type-tested relief valve must be less than or equal to the maximum permissible working pressure of the tank. When using modules SPDB and SPDR at 9 xp (minimum working pressure), a filter with a filtration rating of 6 μm must be used. 1) Connection module type A (see page 74). 2) Connection module with pressure reducing valve type ADB (see page 75). 3) End module type E (see page 78). 4) Intermediate module type Z (page 76). Intermediate modules can also be combined with connection modules. Pos. 1 or can be combined with end module item 3. Length dimensions are calculated by summing the dimension "X" of the directional valve modules (see pages 19 to 21) and the poppet valve modules (see pages 31 to 72). Example: IH15BA006-1X / 07024AA / W220N9K4M01 Nominal size A IH15B assembly up to 14 l/min. With NG6 valve, 7 modules, consecutive numbering 24, variant AA, 220 V AC voltage, N9 manual operation, K4 connection type, sealing material Perbunan, connection type with pipe thread conforming to ISO 228 Part 1. Filter element assembly tool: - With pipe wrench Material number: R904001048. Installation instructions for F30: - Turn the filter cartridge upward to the stop on the stop. Then rotate the filter cartridge approximately 1/3 turns. Installation instructions for DF30 and DF40: - Rotate the filter cartridge as far as possible. Then turn back approximately 1/8 to 1/274 turns.

R904100599 Level switches and temperature switches for clamping and drive modules

Level switch description: The level switch provides electronic monitoring of the hydraulic oil level. If the minimum oil level is reached, the contact opens and outputs a signal to the controller. Technical data: Maximum voltage V 50 AC / DC. Maximum current consumption A 0.25. Maximum power consumption W 3.0. Protection class IP 65. Contact type normally closed contact. Temperature switch (option): The temperature switch protects the clamping and drive module from impermissibly high hydraulic oil temperatures. The temperature switch has a fixed switching point and switches when the hydraulic oil temperature reaches 80 °C. The switch-back hysteresis is approximately 10 K. Technical data: Rated current for 250 V AC 50/60 Hz (cos ϕ 0.95 / 0.60) A 2.5 / 1.6. Rated current for 50 V DC A 0.25. Contact type normally closed contact. Trip temperature °C 80 ± 74 K.

Weidou Intelligent Technology specializes in selling Bosch Rexroth IH15EA-1X/GDH-S350/MNHED8G24V Part No. R904100599 clamping and drive modules, R904100599 control modules, R904100599 drive modules, R904100599 clamping modules, R904100599 Bosch Rexroth modules, UPE1471 clamping and drive modules, R904100599 compact modules, R904100599 motor modules, R904100599 hydraulic modules, R904100599 directional valve modules, R904100599 seat valve modules, IH1484MA modules, IH1484EA modules, R904100599 indexing modules, R904100599 release modules, R904100599 original German imports. Welcome inquiries and orders from users.