Bosch Rexroth UPE5-1X/4, 00A10VSO18ANT-H-0 Part No. R901298643 Clamping and Drive Module Distribution

R901298643 Bosch Rexroth UPE2 Clamping and Drive Module (51142) IH15A Control Module for implementing complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control module can be directly connected to the clamping and drive module UPE2. However, with the help of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be directly mounted on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units of small-volume consumers with a volume flow not exceeding 560 l/min. They are connected to each other via two tie rods. Clamping and drive module

R901298643 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic Module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional Valve Module "W" 1): – Design allowing control using valves with port mounting surfaces conforming to DIN 24340 Form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat Valve Module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH162A". Directional valve modules and seat valve modules can be combined!

R901298643 Notes on Commissioning Clamping and Drive Modules

– Start the clamping and drive module under no-load conditions and let it run at zero pressure for a few seconds to ensure adequate lubrication. – After bleeding the hydraulic oil by moving the hydraulic controls and actuators back and forth several times or by opening available bleed points, refill the hydraulic oil in the clamping and drive module to the correct level. – The clamping and drive module must only be operated within the permitted limits. Operate the module only when there are no objections. – When performing any work on the clamping and drive module, the system must be depressurized and de-energized. – No conversions or modifications that could affect safety and functionality may be carried out without authorization. – Existing protective devices must not be dismantled. – Generally applicable safety regulations and accident prevention rules must be observed. Caution! The clamping and drive module becomes hot during operation => risk of injury! Setting, maintenance, and repair of the clamping and drive module may only be performed by authorized, trained, and instructed personnel. Only original spare parts may be used during repairs!

R901298643 Motors for Clamping and Drive Modules

The clamping and drive modules are designed for short-time operation S2 and intermittent operation S3 within the rated power range, in accordance with VDE 0530 (EN 60034) standards. The motors comply with insulation class F, and the entire clamping and drive module complies with protection rating IP 54. The direction of rotation of the motor depends on the installed pump (see "Technical Data" on page 4). Motor Technical Data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time operation, S3 intermittent operation. Insulation class F (winding). Protection rating IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the "Act on Electromagnetic Compatibility of Equipment" (EEC Directive, Chapter 2, Section 4), the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik from 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-207 Hz. Terminal assignment: Terminal assignment in the terminal box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE5-1X/4, 00A10VSO18ANT-H-0 (part number R901298643) clamping and drive modules, R901298643 control modules, R901298643 drive modules, R901298643 clamping modules, R901298643 Bosch Rexroth modules, UPE1147 clamping and drive modules, R901298643 compact modules, R901298643 motor modules, R901298643 hydraulic modules, R901298643 directional valve modules, R901298643 seat valve modules, IH1160MA modules, IH1160EA modules, R901298643 indexing modules, R901298643 release modules, R901298643 original German imports. Customers are welcome to inquire and place orders.