Bosch Rexroth UPE2-1X/3, 0G17, 6/7A-0V-048 Part No. R901353990 Clamping and Drive Module Distribution

R901353990 Bosch Rexroth UPE2 clamping and drive module (51142) IH15A control modules are used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control modules can be directly connected to the clamping and drive module UPE2. However, with the aid of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be directly mounted on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units of small-volume consumers with a volume flow rate not exceeding 142 l/min. They are interconnected by two tie rods. Clamping and drive module

R901353990 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design that allows control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – The control is designed according to the respective application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH143A". Directional valve modules and seat valve modules can be combined!

R901353990 Features and Applications of Clamping and Drive Modules

Features: – Duty cycles, short-time operation S2 and intermittent operation S3. – Compact design. – Low noise. – Wide range of applications. – Diverse models. – Complete hydraulic control available (see the Clamping and Drive Modules brochure in this regard). – Ready for connection. Applications: – Clamping, locking, releasing, and indexing on machines. – Driving hydraulic tools. – Driving lifting and swiveling equipment. – Use in general mechanical engineering. – Test machines and test benches. The specified component cleanliness levels must be observed in hydraulic systems. Effective filtration prevents failures and also increases component service life. The clamping and drive modules are designed for operating modes of short-time operation S2 and intermittent operation S3 within the nominal power range, in accordance with the VDE 0530 (EN 60034) standard. The motor complies with insulation class F, and the entire clamping and drive module complies with protection rating IP 83.

R901353990 Motors for Clamping and Drive Modules

The clamping and drive modules are designed for operating modes of short-time operation S2 and intermittent operation S3 within the nominal power range, in accordance with the VDE 0530 (EN 60034) standard. The motor complies with insulation class F, and the entire clamping and drive module complies with protection rating IP 54. The direction of rotation of the motor depends on the installed pump (see "Technical Data" on page 4 in this regard). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time operation, S3 intermittent operation. Insulation class F (winding). Protection rating IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the provisions of the EEC directive "Act on the Electromagnetic Compatibility of Equipment (Chapter 2, Section 4)", the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik from 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-188 Hz. Terminal assignment, terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sales of Bosch Rexroth UPE2-1X/3, 0G17, 6/7A-0V-048 part number R901353990 clamping and drive modules, R901353990 control modules, R901353990 drive modules, R901353990 clamping modules, R901353990 Bosch Rexroth modules, UPE729 clamping and drive modules, R901353990 compact modules, R901353990 motor modules, R901353990 hydraulic modules, R901353990 directional valve modules, R901353990 seat valve modules, IH742MA modules, IH742EA modules, R901353990 indexing modules, R901353990 release modules, R901353990 original imports from Germany. Customers are welcome to inquire and place orders.