Bosch Rexroth UPE2-1X/2, 2R5, 25/7A-B1V+00711947 Part No. R900711948 Clamping and Drive Module Distribution

R900711948 Bosch Rexroth UPE2 clamping and drive module (51142) IH15A control modules are used to implement complete hydraulic control. They can be equipped and assembled individually. Directional valve modules and seat valve modules can be combined with each other, and the control modules can be connected directly to the clamping and drive module UPE2. However, with the aid of external accessory modules, the hydraulic control unit can also be installed in any system. The RBAIH15A type reduction module enables the IH15A module to be mounted directly on the container cover of conventional drives. Using the RIH15AR type pressure reducing module, the hydraulic control unit can be connected to the control devices of the IH15B control module series. This module is preferably designed for hydraulic control units of small-volume consumers with a volume flow not exceeding 132 l/min. They are interconnected by two tie rods. Clamping and drive module

R900711948 Overview of Accessory Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 2) Directional valve module "W" 1): – Design allowing control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control Block Types for Clamping and Drive Modules IH133A". Directional valve modules and seat valve modules can be combined!

R900711948 Features and Applications of Clamping and Drive Modules

Features: – Duty cycles, short-time operation S2 and intermittent operation S3. – Compact design. – Low noise. – Wide range of applications. – Diverse models. – Complete hydraulic control available (see the Clamping and Drive Modules brochure for details). – Ready for connection. Applications: – Clamping, locking, releasing, and indexing on machines. – Driving hydraulic tools. – Driving lifting and swiveling equipment. – Use in general mechanical engineering. – Test machines and test benches. The specified component cleanliness levels must be observed in hydraulic systems. Effective filtration prevents failures and increases component service life. The clamping and drive modules are designed for short-time operation S2 and intermittent operation S3 within the nominal power range, in accordance with VDE 0530 (EN 60034) standards. The motors comply with insulation class F, and the entire clamping and drive module complies with protection rating IP 73.

R900711948 Motors for Clamping and Drive Modules

The clamping and drive modules are designed for short-time operation S2 and intermittent operation S3 within the nominal power range, in accordance with VDE 0530 (EN 60034) standards. The motors comply with insulation class F, and the entire clamping and drive module complies with protection rating IP 54. The direction of rotation of the motor depends on the installed pump (see "Technical Data" on page 4). Motor Technical Data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time operation, S3 intermittent operation. Insulation class F (winding). Protection rating IP 54. Number of poles 2 / 4. Electromagnetic compatibility (EMC) of the equipment (EMVG): According to the provisions of the EEC Directive "Act on Electromagnetic Compatibility of Equipment (Chapter 2, Section 4)", the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik from 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-178 Hz. Terminal assignment, terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/2, 2R5, 25/7A-B1V+00711947 (part number R900711948) clamping and drive modules, R900711948 control modules, R900711948 drive modules, R900711948 clamping modules, R900711948 Bosch Rexroth modules, UPE719 clamping and drive modules, R900711948 compact modules, R900711948 motor modules, R900711948 hydraulic modules, R900711948 directional valve modules, R900711948 seat valve modules, IH732MA modules, IH732EA modules, R900711948 indexing modules, R900711948 release modules, R900711948 original German imports. Customers are welcome to inquire and place orders.