Bosch Rexroth UPE2-1X/2, 2G1, 40/7A-B1V+R901153794 Part No. R901153795 Clamping and Drive Module Distribution

R901153795 Bosch Rexroth UPE 2 clamping and drive modules constitute a complete drive system that is ready for connection upon delivery. They are used to supply hydraulic oil to the hydraulic circuit. Due to thermal load considerations, the clamping and drive modules operate in short-time duty and intermittent duty modes. The duty cycle is selected based on power output and environmental conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module operates in a vertical mounting position. Optionally, the UPE 55 clamping and drive module can be equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R901153795 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding pressure functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control block types for clamping and drive modules. IH15A". 2) Directional valve module "W" 1): – Design allowing control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of a seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH68A". Directional valve modules and seat valve modules can be combined!

R901153795 Commissioning notes for clamping and drive modules

– Please check whether the clamping and drive module has been professionally connected (hydraulically and electrically) to the machine to be operated. – For the electrical connection of the motor, the shims and connection bridges included in the scope of delivery must be used. – The motor must be protected by equipment with an overload relay. The latter must be set to the nominal current indicated on the nameplate/rating plate. – When installing the clamping and drive module on an external gear pump, the direction of rotation of the motor must be strictly observed; see the arrow indicating the direction of rotation. (Practical check: Briefly switch on the motor and check whether the pump can transfer fluid.) (Visual check: Remove the air filter on the tank cover, briefly switch on the motor, and check the direction of rotation of the rotor shaft.) – Hydraulic oil may only be filled through a filter with the required minimum retention rate. – The clamping and drive module must be filled with hydraulic oil to the maximum level, until the oil gauge reaches the lower edge of the cover. – Under no circumstances should the clamping and drive module be operated without hydraulic oil.

R901153795 Motor for clamping and drive modules

The clamping and drive modules are designed for operation in short-time duty S2 and intermittent duty S3 modes within the rated power range, in accordance with standard VDE 0530 (EN 60034). The motor complies with insulation class F, and the entire clamping and drive module complies with protection class IP 54. The direction of rotation of the motor depends on the installed pump (see "Technical Data" on page 4). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time duty, S3 intermittent duty. Insulation class F (windings). Protection class IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the provisions of the "Act on Electromagnetic Compatibility of Equipment" under the EEC directive (Chapter 2, Section 4), the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik of 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-113 Hz. Terminal assignment: Terminal assignment in the terminal box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/2, 2G1, 40/7A-B1V+R901153794 (Item No. R901153795) clamping and drive modules, R901153795 control modules, R901153795 drive modules, R901153795 clamping modules, R901153795 Bosch Rexroth modules, UPE454 clamping and drive modules, R901153795 compact modules, R901153795 motor modules, R901153795 hydraulic modules, R901153795 directional valve modules, R901153795 seat valve modules, IH467MA modules, IH467EA modules, R901153795 indexing modules, R901153795 release modules, R901153795 original imports from Germany. Customers are welcome to inquire and place orders.