Bosch Rexroth UPE2-1X/1, 1R2, 60/3A-1V-026+00992205 Part No. R900718899 Clamping and Drive Module Distribution

R900718899 Bosch Rexroth UPE 2 clamping and drive modules constitute a complete drive system that is ready for connection upon delivery. It is used to supply hydraulic oil to the hydraulic circuit. For reasons related to thermal load, the clamping and drive module will operate in short-time duty and intermittent duty modes. The duty cycle is selected based on power output and environmental conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module will operate in a vertical mounting position. Optionally, the UPE 18 clamping and drive module can be equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R900718899 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding pressure functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control block types for clamping and drive modules. IH15A". 2) Directional valve module "W" 1): – Allows control designs using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH31A". Directional valve modules and seat valve modules can be combined!

R900718899 Notes on commissioning clamping and drive modules

– Please check whether the clamping and drive module has been professionally connected (hydraulically and electrically) to the machine to be operated. – For the electrical connection of the motor, the washers and connection bridges included in the delivery scope must be used. – The motor must be protected by equipment with an overload relay. The latter must be set to the nominal current indicated on the nameplate/rating plate. – When installing the clamping and drive module on an external gear pump, the rotation direction of the motor must be strictly observed; see the arrow indicating the rotation direction. (Practical check: Briefly switch on the motor and check if the pump can transfer fluid.) (Visual check: Remove the air filter on the tank cover, briefly switch on the motor, and check the rotation direction of the rotor shaft.) – Hydraulic oil must only be injected through a filter with the required minimum retention rate. – The clamping and drive module must be filled with hydraulic oil to the maximum level, until the oil dipstick reaches the lower edge of the cover. – Under no circumstances should the clamping and drive module be operated without hydraulic oil.

R900718899 Motor for clamping and drive modules

The clamping and drive module is designed for operation in short-time duty S2 and intermittent duty S3 modes within the nominal power range, in accordance with standards VDE 0530 (EN 60034). The motor conforms to insulation class F, and the entire clamping and drive module conforms to protection class IP 54. The rotation direction of the motor depends on the installed pump (see "Technical Data" on page 4 for this point). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time duty, S3 intermittent duty. Insulation class F (windings). Protection class IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the provisions of the EEC directive "Act concerning electromagnetic compatibility of equipment (Chapter 2, Section 4)", the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik of 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-76 Hz. Terminal assignment: Terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/1, 1R2, 60/3A-1V-026+00992205 item number R900718899 clamping and drive modules, R900718899 control modules, R900718899 drive modules, R900718899 clamping modules, R900718899 Bosch Rexroth modules, UPE417 clamping and drive modules, R900718899 compact modules, R900718899 motor modules, R900718899 hydraulic modules, R900718899 directional valve modules, R900718899 seat valve modules, IH430MA modules, IH430EA modules, R900718899 indexing modules, R900718899 release modules, R900718899 original German imports. Customers are welcome to inquire and place orders.