Bosch Rexroth UPE2-1X/1, 1R1, 95/4AT-B1V+00333690 Part No. R900334114 Clamping and Drive Module Distribution

R900334114 Bosch Rexroth UPE 2 clamping and drive modules constitute a complete drive system that is ready for connection upon delivery. It is used to supply hydraulic oil to the hydraulic circuit. For reasons related to thermal load, the clamping and drive module will operate in short-time and intermittent duty modes. The duty cycle is selected based on power output and environmental conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module will operate in a vertical installation position. The UPE 69 clamping and drive module can optionally be equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R900334114 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control block types for clamping and drive modules. IH15A". 2) Directional valve module "W" 1): – Allows control designs using valves with porting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the relevant application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH82A". Directional valve modules and seat valve modules can be combined!

R900334114 Technical data for clamping and drive modules

Hydraulic oil conforms to mineral oils (HLP) according to DIN 51524 Part 2 (HLP). Please strictly observe the specifications in catalog 07075! Hydraulic oil temperature range °C –20 to +80. Maximum permissible contamination level for hydraulic oil cleanliness class conforms to ISO 440 (c), Class 20/18/15 4). Optimal viscosity range mm2/s 10 to 200. Rotation direction optional (radial piston pump), clockwise (external gear pump). Installation position vertical. Operating mode All operating modes where the steady-state oil temperature remains below 80 °C. Radial piston pump flow 3) qV (l/min) 0.49 0.82 1.00 2) 1.25 1.70 2) 1.95 2.55 2) 2.60 4.00 2). Drive power speed 3) n (min–1) 1380 1380 2820 1380 2820 1380 2820 1380 2820 1.1 kW 1) Nominal pressure 3) pmax (bar) 700 700 700 450 310 250 200 180 140. Speed 3) n (min–1) 1400 1400 2890 1400 2890 1400 2890 1400 2890. 2.2 kW 1) Nominal pressure 3) pmax (bar) 700 700 700 450 700 350 450 250 280. External gear pump flow 3) qV (l/min) 1.40 2.80 4.40 5.60 7.00 8.80 11.2 2) 14.0 2). Drive power speed 3) n (min–1) 1380 1380 1380 1380 1380 1380 2820 2820. 1.1 kW 1) Nominal pressure 3) pmax (bar) 260 180 140 110 90 70 45 37. Speed 3) n (min–1) 1400 1400 1400 1400 1400 1400 2890 2890. 2.2 kW 1) Nominal pressure 3) pmax (bar) 260 260 260 220 170 140 110 85. Protection class IP 54 (with fully installed hydraulic power unit) in accordance with VDE 0530 / EN 60034. Tank nominal size/type 3/R 4/R 4/G 5/R 7/R 7/G. Weight (without hydraulic oil) kg 17.8 18.4 19.6 23.0 25.0 26.6. 1) See performance charts below 2) Not available at 60 Hz! 3) Refers to speed at 50 Hz 71) The specified component cleanliness levels must be observed in the hydraulic system. Effective filtration prevents failures and also increases component service life. For filter selection, see catalog Clamping and Drive Modules.

R900334114 Air filters and oil trays for clamping and drive modules

Air filter (option): We recommend using an air filter when operating the clamping and drive module in heavily contaminated environments. During installation, the connection between the air filter and the engine intake pipe, whether via flange, rubber hose, or direct connection, must be tight and reliable to prevent air leaks. Rubber gaskets must be installed on both ends of the filter element. The wing nuts securing the air filter cover must not be overtightened to avoid crushing the paper filter element. During use, strictly prevent the paper-core air filter from getting wet by rain, as absorbing a large amount of water will significantly increase intake resistance and shorten service life. In addition, paper-core air filters must not come into contact with oil or fire. Oil tray (option) (dimensions in mm): Size 3 and Size 4 Material No. R901109231, Size 5 and Size 7 Material No. R901109235, Color: RAL 7102 "Light gray."

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/1, 1R1, 95/4AT-B1V+00333690 part number R900334114 clamping and drive modules, R900334114 control modules, R900334114 drive modules, R900334114 clamping modules, R900334114 Bosch Rexroth modules, UPE368 clamping and drive modules, R900334114 compact modules, R900334114 motor modules, R900334114 hydraulic modules, R900334114 directional valve modules, R900334114 seat valve modules, IH381MA modules, IH381EA modules, R900334114 indexing modules, R900334114 release modules, R900334114 original German imports. Customers are welcome to inquire and place orders.