Bosch Rexroth UPE2-1X/1, 1R1, 25/3AN-1V+04101668 Part No. R904101669 Clamping and Drive Module Distribution

R904101669 Bosch Rexroth UPE 2 clamping and drive modules constitute a complete drive system that is ready for connection upon delivery. They are used to supply hydraulic oil to the hydraulic circuit. Due to thermal load considerations, the clamping and drive modules operate in short-time and intermittent duty modes. The duty cycle is selected based on power output and ambient conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module operates in a vertical installation position. The UPE 139 clamping and drive module can optionally be equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R904101669 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control block types for clamping and drive modules. IH15A". 2) Directional valve module "W" 1): – Design allowing control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of a seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH152A". Directional valve modules and seat valve modules can be combined!

R904101669 Technical data for clamping and drive modules

Hydraulic oil: Mineral oil (HLP) according to DIN 51524 Part 2 (HLP). Please strictly observe the specifications in catalog 07075! Hydraulic oil temperature range °C –20 to +80. Maximum permissible contamination level for hydraulic oil cleanliness class according to ISO 440 (c), Class 20/18/15 4). Optimal viscosity range mm2/s 10 to 200. Direction of rotation: Optional (radial piston pump), clockwise (external gear pump). Installation position: Vertical. Operating mode: All operating modes where the steady-state oil temperature remains below 80 °C. Radial piston pump flow 3) qV (l/min) 0.49 0.82 1.00 2) 1.25 1.70 2) 1.95 2.55 2) 2.60 4.00 2). Drive power speed 3) n (min–1) 1380 1380 2820 1380 2820 1380 2820 1380 2820 1.1 kW 1) Nominal pressure 3) pmax (bar) 700 700 700 450 310 250 200 180 140. Speed 3) n (min–1) 1400 1400 2890 1400 2890 1400 2890 1400 2890. 2.2 kW 1) Nominal pressure 3) pmax (bar) 700 700 700 450 700 350 450 250 280. External gear pump flow 3) qV (l/min) 1.40 2.80 4.40 5.60 7.00 8.80 11.2 2) 14.0 2). Drive power speed 3) n (min–1) 1380 1380 1380 1380 1380 1380 2820 2820. 1.1 kW 1) Nominal pressure 3) pmax (bar) 260 180 140 110 90 70 45 37. Speed 3) n (min–1) 1400 1400 1400 1400 1400 1400 2890 2890. 2.2 kW 1) Nominal pressure 3) pmax (bar) 260 260 260 220 170 140 110 85. Protection class IP 54 (with fully installed hydraulic power unit) according to VDE 0530 / EN 60034. Tank nominal size/type 3/R 4/R 4/G 5/R 7/R 7/G. Weight (without hydraulic oil) kg 17.8 18.4 19.6 23.0 25.0 26.6. 1) See performance charts below 2) Not available at 60 Hz! 3) Refers to speed at 50 Hz 141) The specified component cleanliness levels must be observed in the hydraulic system. Effective filtration prevents failures and increases component service life. For filter selection, see the Clamping and Drive Modules catalog.

R904101669 Level switches and temperature switches for clamping and drive modules

Level switch description: Level switches provide electronic monitoring of the hydraulic oil level. If the minimum oil level is reached, the contacts open and output a signal to the controller. Technical data: Max. voltage V 50 AC / DC. Max. current consumption A 0.25. Max. power consumption W 3.0. Protection class IP 65. Contact type: Normally closed. Temperature switch (option): The temperature switch protects the clamping and drive module from impermissibly high hydraulic oil temperatures. The temperature switch has a fixed switching point and trips when the hydraulic oil temperature reaches 80 °C. The reset hysteresis is approximately 10 K. Technical data: Nominal current (cos ϕ 0.95 / 0.60) A 2.5 / 1.6 for 250 V AC 50/60 Hz. Nominal current A 0.25 for 50 V DC. Contact type: Normally closed. Trip temperature °C 80 ± 89 K.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/1, 1R1, 25/3AN-1V+04101668 (Item No. R904101669) clamping and drive modules, R904101669 control modules, R904101669 drive modules, R904101669 clamping modules, R904101669 Bosch Rexroth modules, UPE287 clamping and drive modules, R904101669 compact modules, R904101669 motor modules, R904101669 hydraulic modules, R904101669 directional valve modules, R904101669 seat valve modules, IH300MA modules, IH300EA modules, R904101669 indexing modules, R904101669 release modules, R904101669. Original imports from Germany. Inquiries and orders are welcome.