Bosch Rexroth UPE2-1X/1, 1R0, 82/3A-B1V+04100299 Part No. R904100300 Clamping and Drive Module Distribution

R904100300 Bosch Rexroth UPE 2 clamping and drive modules constitute a complete drive system that is ready for connection upon delivery. They are used to supply hydraulic oil to the hydraulic circuit. Due to thermal load considerations, the clamping and drive modules operate in short-time duty and intermittent duty modes. The duty cycle is selected based on power output and ambient conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module will operate in a vertical mounting position. Optionally, the UPE 200 clamping and drive module can be equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R904100300 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control block types for clamping and drive modules. IH15A". 2) Directional valve module "W" 1): – Design allowing control using valves with porting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control block types for clamping and drive modules IH213A". Directional valve modules and seat valve modules can be combined!

R904100300 Features and applications of clamping and drive modules

Features: – Duty cycle, short-time duty S2 and intermittent duty S3. – Compact design. – Low noise. – Wide range of applications. – Diverse models. – Complete hydraulic control available (see catalog Clamping and Drive Modules). – Ready for connection. Applications: – Clamping, locking, releasing, and indexing on machines. – Driving hydraulic tools. – Driving lifting and swiveling equipment. – Use in general mechanical engineering. – Test machines and test benches. The specified component cleanliness levels must be observed in hydraulic systems. Effective filtration prevents failures and increases component service life. The clamping and drive modules are designed for operation in short-time duty S2 and intermittent duty S3 modes within the nominal power range, in accordance with standards VDE 0530 (EN 60034). The motor conforms to insulation class F, and the entire clamping and drive module conforms to protection class IP 153.

R904100300 Motors for clamping and drive modules

The clamping and drive modules are designed for operation in short-time duty S2 and intermittent duty S3 modes within the nominal power range, in accordance with standards VDE 0530 (EN 60034). The motor conforms to insulation class F, and the entire clamping and drive module conforms to protection class IP 54. The direction of rotation of the motor depends on the installed pump (see "Technical Data" on page 4). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time duty, S3 intermittent duty. Insulation class F (windings). Protection class IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the provisions of the EEC directive "Act on Electromagnetic Compatibility of Equipment (Chapter 2, Section 4)", the clamping and drive module is not a ready-to-use device. To avoid potential electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik of 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-258 Hz. Terminal assignment, terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/1, 1R0, 82/3A-B1V+04100299 item number R904100300 clamping and drive modules, R904100300 control modules, R904100300 drive modules, R904100300 clamping modules, R904100300 Bosch Rexroth modules, UPE200 clamping and drive modules, R904100300 compact modules, R904100300 motor modules, R904100300 hydraulic modules, R904100300 directional valve modules, R904100300 seat valve modules, IH213MA modules, IH213EA modules, R904100300 indexing modules, R904100300 release modules, R904100300 original imports from Germany. Customers are welcome to inquire and place orders.