Bosch Rexroth UPE2-1X/1, 1G7, 00/4A-1V+R901090429 Part No. R901090438 Clamping and Drive Module Distribution

R901090438 The Bosch Rexroth UPE 2 clamping and drive module constitutes a complete drive system that is ready for connection upon delivery. It is used to supply hydraulic oil to the hydraulic circuit. For reasons related to thermal load, the clamping and drive module will operate in short-time duty and intermittent duty modes. The duty cycle is selected based on power output and environmental conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module will operate in a vertical installation position. The UPE 128 clamping and drive module can be optionally equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R901090438 Overview of accessory modules for clamping and drive modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding pressure functions. – If the basic module "G" is used, further stacking is not feasible. – For more details, see the brochure "Control block types for clamping and drive modules. IH15A". 2) Directional valve module "W" 1): – Allows a design for control using valves with port mounting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control block types for clamping and drive modules IH15A". 3) Seat valve module "S" 1): – The basic composition of the seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the relevant application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see the brochure "Control block types for clamping and drive modules IH141A". Directional valve modules and seat valve modules can be combined!

R901090438 Features and applications of clamping and drive modules

Features: – Duty cycles: short-time duty S2 and intermittent duty S3. – Compact design. – Low noise. – Wide range of applications. – Diverse models. – Complete hydraulic control available (see the brochure Clamping and Drive Modules for details). – Ready for connection. Applications: – Clamping, locking, releasing, and indexing on machines. – Driving hydraulic tools. – Driving lifting and swiveling equipment. – Use in general mechanical engineering. – Test machines and test benches. The specified component cleanliness levels must be observed in hydraulic systems. Effective filtration prevents failures and increases component service life. The clamping and drive module is designed for operating modes of short-time duty S2 and intermittent duty S3 within the nominal power range, in accordance with the VDE 0530 (EN 60034) standard. The motor conforms to insulation class F, and the entire clamping and drive module conforms to protection class IP 81.

R901090438 Motors for clamping and drive modules

The clamping and drive module is designed for operating modes of short-time duty S2 and intermittent duty S3 within the nominal power range, in accordance with the VDE 0530 (EN 60034) standard. The motor conforms to insulation class F, and the entire clamping and drive module conforms to protection class IP 54. The direction of rotation of the motor depends on the installed pump (see "Technical Data" on page 4). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time duty, S3 intermittent duty. Insulation class F (windings). Protection class IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the provisions of the EEC directive "Act on Electromagnetic Compatibility of Equipment (Chapter 2, Section 4)", the clamping and drive module is not a ready-to-use device. To avoid possible electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik of 71570 Oppenweiler. For example, type 23050, 3 x 400 VAC, 50-186 Hz. Terminal assignment: Terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/1, 1G7, 00/4A-1V+R901090429 item number R901090438 clamping and drive modules, R901090438 control modules, R901090438 drive modules, R901090438 clamping modules, R901090438 Bosch Rexroth modules, UPE128 clamping and drive modules, R901090438 compact modules, R901090438 motor modules, R901090438 hydraulic modules, R901090438 directional valve modules, R901090438 seat valve modules, IH141MA modules, IH141EA modules, R901090438 indexing modules, R901090438 release modules, R901090438 original German imports. Customers are welcome to inquire and place orders.