Bosch Rexroth UPE2-1X/1, 1G2, 80/4A-BT1V+04100105 Part No. R904100331 Clamping and Drive Module Distribution

R904100331 Bosch Rexroth UPE 2 clamping and drive modules constitute a complete drive system that is ready for connection upon delivery. They are used to supply hydraulic oil to the hydraulic circuit. Due to thermal load considerations, the clamping and drive modules operate in short-time duty and intermittent duty modes. The duty cycle is selected based on power output and environmental conditions so that the maximum permissible operating temperature of 80 °C is not exceeded. The clamping and drive module basically consists of an aluminum housing, a pump (radial piston pump or external gear pump), and an oil-immersed motor. The stator of the oil-immersed motor is pressed into the aluminum housing. It transfers the heat from the windings directly to the outer wall of the aluminum housing. For installation, four through-holes for mounting screws are provided at the bottom of the tank. The clamping and drive module operates in a vertical installation position. The UPE 73 clamping and drive module can optionally be equipped with electronic monitors for oil level and oil temperature monitoring, air filters, and complete hydraulic control. Clamping and drive module

R904100331 Overview of Accessories Modules for Clamping and Drive Modules

1) Basic module "G": – Basic module with integrated relief valve for simple lowering and holding pressure functions. – If basic module "G" is used, further stacking is not feasible. – For more details, see catalog "Control Block Types for Clamping and Drive Modules. IH15A". 2) Directional valve module "W" 1): – Design allowing control using valves with porting surfaces conforming to DIN 24340 form A. – The number of directional valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH15A". 3) Seat valve module "S" 1): – The basic composition of a seat valve includes: • One relief valve block. • One or several control blocks. • One end block. – Control is designed according to the specific application. – The number of seat valve modules depends on the discharge volume and pump displacement. – For more details, see catalog "Control Block Types for Clamping and Drive Modules IH86A". Directional valve modules and seat valve modules can be combined!

R904100331 Technical Data for Clamping and Drive Modules

Hydraulic oil: Mineral oil (HLP) according to DIN 51524 Part 2 (HLP). Please strictly observe the specifications in catalog 07075! Hydraulic oil temperature range °C –20 to +80. Maximum permissible contamination level for hydraulic oil cleanliness class according to ISO 440 (c), Class 20/18/15 4). Optimal viscosity range mm2/s 10 to 200. Direction of rotation: Optional (radial piston pump), clockwise (external gear pump). Installation position: Vertical. Operating mode: All operating modes where the steady-state oil temperature remains below 80 °C. Radial piston pump flow 3) qV (l/min) 0.49 0.82 1.00 2) 1.25 1.70 2) 1.95 2.55 2) 2.60 4.00 2). Drive power speed 3) n (min–1) 1380 1380 2820 1380 2820 1380 2820 1380 2820 1.1 kW 1) Nominal pressure 3) pmax (bar) 700 700 700 450 310 250 200 180 140. Speed 3) n (min–1) 1400 1400 2890 1400 2890 1400 2890 1400 2890. 2.2 kW 1) Nominal pressure 3) pmax (bar) 700 700 700 450 700 350 450 250 280. External gear pump flow 3) qV (l/min) 1.40 2.80 4.40 5.60 7.00 8.80 11.2 2) 14.0 2). Drive power speed 3) n (min–1) 1380 1380 1380 1380 1380 1380 2820 2820. 1.1 kW 1) Nominal pressure 3) pmax (bar) 260 180 140 110 90 70 45 37. Speed 3) n (min–1) 1400 1400 1400 1400 1400 1400 2890 2890. 2.2 kW 1) Nominal pressure 3) pmax (bar) 260 260 260 220 170 140 110 85. Protection class IP 54 according to VDE 0530 / EN 60034 (with fully installed hydraulic power unit). Tank nominal size/type 3/R 4/R 4/G 5/R 7/R 7/G. Weight (without hydraulic oil) kg 17.8 18.4 19.6 23.0 25.0 26.6. 1) See performance charts below 2) Not available at 60 Hz! 3) Refers to speed at 50 Hz 75) The specified component cleanliness levels must be observed in the hydraulic system. Effective filtration prevents failures and increases component service life. For filter selection, see the Clamping and Drive Modules catalog.

R904100331 Motors for Clamping and Drive Modules

Clamping and drive modules are designed for short-time duty S2 and intermittent duty S3 operating modes within the nominal power range, in accordance with standards VDE 0530 (EN 60034). The motor conforms to insulation class F, and the entire clamping and drive module conforms to protection class IP 54. The direction of rotation of the motor depends on the installed pump (see "Technical Data" on page 4). Motor technical data Voltage 1) U V 230 / 400 ±6 % Δ/Y. Frequency f Hz 50 / 60. Operating mode S2 short-time duty, S3 intermittent duty. Insulation class F (windings). Protection class IP 54. Number of poles 2 / 4. Electromagnetic compatibility of the equipment (EMVG): According to the "Act on Electromagnetic Compatibility of Equipment" (EEC Directive, Chapter 2, Section 4), the clamping and drive module is not a ready-to-use device. To avoid potential electromagnetic interference, we recommend using interference suppression components manufactured by Murr-Elektronik of 71570 Oppenweiler, such as type 23050, 3 x 400 VAC, 50-131 Hz. Terminal assignment: Terminal assignment in the junction box on the clamping and drive module.

Weidou Intelligent Technology specializes in the sale of Bosch Rexroth UPE2-1X/1, 1G2, 80/4A-BT1V+04100105 item number R904100331 clamping and drive modules, R904100331 control modules, R904100331 drive modules, R904100331 clamping modules, R904100331 Bosch Rexroth modules, UPE73 clamping and drive modules, R904100331 compact modules, R904100331 motor modules, R904100331 hydraulic modules, R904100331 directional valve modules, R904100331 seat valve modules, IH86MA modules, IH86EA modules, R904100331 indexing modules, R904100331 release modules, R904100331 original imports from Germany. Customers are welcome to inquire and place orders.