TET 7-10 seals Germany thorsman model TET 7-10 price

TET 7-10 seals are devices that prevent fluid leakage, consisting of at least one pair of faces perpendicular to the axis of rotation that remain in contact and slide relative to each other under the action of fluid pressure and the elastic force (or magnetic force) of a compensation mechanism, together with auxiliary seals. Mechanical seals where the elastic loading mechanism and auxiliary seal are metal bellows are referred to as metal bellows seals. In light-duty seals, rubber bellows are also used as auxiliary seals; since the elastic force of rubber bellows is limited, springs are generally required to supplement the loading force. Mechanical seals are commonly abbreviated as "mech seals".

TET 7-10 seals introduction

A mechanical seal is a shaft sealing device for rotating machinery, such as centrifugal pumps, centrifuges, reaction vessels, and compressors. Since the drive shaft passes through the interior and exterior of the equipment, there is a circumferential gap between the shaft and the equipment. The medium inside the equipment leaks outward through this gap; if the pressure inside the equipment is lower than atmospheric pressure, air leaks into the equipment. Therefore, a shaft sealing device is required to prevent leakage. There are many types of shaft seals. Due to advantages such as low leakage and long service life, mechanical seals are the primary shaft sealing method for these equipment worldwide. Mechanical seals are also called face seals. National standards define them as: "a device that prevents fluid leakage, consisting of at least one pair of faces perpendicular to the axis of rotation that remain in contact and slide relative to each other under the action of fluid pressure and the elastic force (or magnetic force) of a compensation mechanism, together with auxiliary seals."

TET 7-10 seals structure and composition

1) Main components: rotating ring, stationary ring, cooling device, and compression spring (depending on the specific equipment). 2) Auxiliary seals: O-rings (O-shaped, X-shaped, U-type, wedge-shaped, rectangular flexible graphite, PTFE-covered rubber O rings, etc.). 3) Elastic compensation mechanism: springs, thrust rings, spring seats, keys, or various screws. 4) Classification: single-face, double-face; balanced, unbalanced; arbitrary rotation direction, fixed rotation direction.

TET 7-10 seals installation precautions

1) During installation, pay close attention to avoid installation deviations. Tighten the gland after aligning the coupling. Bolts should be tightened evenly to prevent tilting of the gland face. Check all points with a feeler gauge; the error must not exceed 0.05 mm. Check the fit clearance (i.e., concentricity) between the gland and the outer diameter of the shaft or shaft sleeve; it must be uniform around the circumference. Check all points with a feeler gauge; the permissible error must not exceed 0.01 mm. 2) Spring compression must be performed according to regulations; excessive or insufficient compression is not allowed. The required error is 2.00 mm. Excessive compression increases the specific face pressure, accelerating face wear. Insufficient compression results in inadequate specific pressure, failing to achieve sealing. 3) After installing the rotating ring, it should automatically spring back when pressed against the spring. 4) Installation position requirements: To ensure stable operation, long service life, and low leakage performance of the mechanical seal, correct installation on the machine is crucial. When installing the mechanical seal on the machine, compare it carefully with the general assembly drawing before installation to confirm that all parts are ready. Pay attention to any abnormalities such as scratches or damage on the sealing friction faces and O-rings. Also check for scratches on the surfaces of the shaft or shaft sleeve and flanges that come into contact with packing and O-rings (O rings). If any abnormalities are found, replace or repair before use. During actual installation, do not bring more parts to the site than needed. If parts remain after installation, it indicates missing components during installation; if parts are insufficient, it means unnecessary components were assembled, thus serving as a self-check during installation.

Weidou Intelligent Technology professionally sells German thorsman seals, TET 7-10 O-rings, TET 7-10 sealing strips, TET 7-10 pipe seals, TET 7-10 cable seals, TET 7-10 rubber seals, TET 7-10 mechanical seals, TET 7-10 gaskets, TET 7-10 oil seals, TET 7-10 shaft seals, TET 7-10 metal seals, TET 7-10 high-pressure seals, TET 7-10 spiral seals, TET 7-10 centrifugal seals, TET 7-10 sealing rings, TET 7-10 original German imports. Welcome customers to inquire and order.