German WALTON tools WALTON models WALTON prices

WALTON tools integrate hydraulic systems with conventional tools into a unified assembly. They convert powerful hydraulic power into mechanical motions such as reciprocating linear motion, rotary motion, and orbital motion. A complete hydraulic tool system consists of five components: power elements, actuating elements, control elements, auxiliary elements, and hydraulic oil. Hydraulic tools include: hydraulic wrenches, electric pumps dedicated to hydraulic wrenches, hydraulic jacks, hydraulic bolt tensioners, hydraulic flange spreaders, hydraulic nut splitters, hydraulic pullers, etc. Hydraulic tools offer the advantages of high efficiency and convenience. A complete hydraulic tool system consists of five components: power elements, actuating elements, control elements, auxiliary elements, and hydraulic oil.

WALTON tool types

1) Frame saw. Also known as a sash saw, it consists of an I-shaped wooden frame, twisted rope and twist pieces, and a saw blade. The two ends of the saw blade are fixed to the frame with knobs, which can also be used to adjust the angle of the blade. After the twisted rope is tightened, the saw blade is taut and ready for use. Frame saws are classified into coarse, medium, and fine types based on blade length and tooth pitch. Coarse saw blades are 650—750mm long, with a tooth pitch of 4—5mm; coarse saws are mainly used for cutting thicker lumber. Medium saw blades are 550—650mm long, with a tooth pitch of 3—4mm; medium saws are mainly used for cutting thin lumber or cutting tenons. Fine saw blades are 450—500mm long, with a tooth pitch of 2—3mm; fine saws are mainly used for cutting finer wood and cutting tenon shoulders. 2) Knife saw. A knife saw mainly consists of two parts: the saw edge and the saw handle. It can be classified into single-sided, double-sided, and backed knife saws. Single-sided knife saws have a blade length of 350mm, with teeth on one side; depending on the function of the teeth, they can be divided into rip cuts and crosscuts. Double-sided knife saws have a blade length of 300mm, with teeth on both sides; typically, one side is for rip cutting and the other for crosscutting. Backed knife saws have a blade plate length of 250—300mm; the back of the backed knife saw is reinforced straight with a steel strip, and the teeth are finer, available as rip or crosscut saws. 3) Groove saw. A groove saw consists of a handle and a saw blade, with the blade being approximately 200mm long. Groove saws are mainly used for cutting grooves in wood. 4) Panel saw. Also known as a hand saw. It consists of a handle and a saw blade, with the blade being approximately 250—750mm long and a tooth pitch of 3—4mm. Panel saws are mainly used for cutting wider boards. 5) Narrow hand saw. The blade is narrow and long, with a pointed tip, and a length of approximately 300—400mm. Narrow hand saws are mainly used for cutting narrow holes and slots. 6) Coping saw. Also known as a fret saw, its construction is similar to that of a frame saw, but the blade is narrower (approximately 10mm), mainly used for cutting arcs, curves, and similar shapes. 7) Wire saw. Also known as a bow saw, it is made by bending a bamboo strip into a bow shape, with steel wire stretched between the two ends. Saw-tooth-like projections are cut into the steel wire, using the sharp edges of these projections for cutting. The steel wire is approximately 200—600mm long, and the saw bow is 800—900mm long. Wire saws are mainly used for cutting complex curves and opening holes.

WALTON tool maintenance

1) Correct air supply system: The intake pressure at the tool inlet (not the compressor outlet pressure) is generally 90PSIG (6.2Kg/cm^2). Pressure that is too high or too low will impair tool performance and service life. The intake air must contain sufficient lubricating oil to ensure adequate lubrication of the pneumatic motor inside the tool (place a white paper at the tool exhaust to check for oil stains; the presence of oil stains is normal). The intake air must be free of moisture; using compressed air without an air dryer is inappropriate. 2) Do not arbitrarily disassemble tool parts before operation, as this may compromise operator safety and cause tool damage. 3) If the tool has a slight fault or fails to achieve its original function after use, do not continue using it; inspect it immediately. 4) Regularly (approximately once a week) inspect and maintain the tool, adding grease (Grease) to rotating parts such as bearings, and adding oil (Oil) to the pneumatic motor. 5) When using various tools, strictly adhere to all safety regulations and operating instructions. 6) Select appropriate tools for the job; oversized tools can easily cause work-related injuries, while undersized tools can easily lead to tool damage.

WALTON tool usage

1) When placing the diamond dressing tool holder into the collet, take care not to impact the grinding wheel surface. 2) Do not align a single-point diamond dressing tool holder vertically with the center of the grinding wheel; it generally needs to be tilted 10-15°. 3) Do not "quench" (i.e., suddenly cool) a heated dressing tool. During dry dressing, maintain sufficient interval time between dressings to allow the heated dressing tool to cool. 4) Do not assume the grinding wheel surface is ideally flat. At the start of dressing, locate the high points on the grinding wheel and proceed with dressing. 5) If possible, the amount removed from the grinding wheel during each dressing should not exceed 0.001 inches on the wheel radius. Excessive removal can cause premature wear and frequent fracture of the diamond dressing tool holder. 6) However, do not remove too little material each time. Grinding wheels used on old or poorly rigid machine tools may not require dressing. 7) Note that the dressing tool should not remain in one position for too long. This will polish the grinding wheel surface, generate high temperatures, and damage the diamond dressing tool. Rotate the dressing tool at least once a day. 8) Do not continue to use worn or damaged dressing tools. Adjust or replace them promptly. 9) Do not select excessive removal amounts and too fast lateral feed rates during rough dressing, followed by small removal amounts and slow lateral feed rates during finish dressing. This will quickly damage the diamond dressing tool. If possible, it is recommended to select the same lateral feed rate for both rough and finish dressing.

Weidou Intelligent Technology professionally sells German WALTON workpiece clamps, WALTON hydraulic tools, WALTON power tools, WALTON pneumatic tools, WALTON hand tools, WALTON electronic tools, WALTON welding tools, WALTON piping tools, WALTON explosion-proof tools, WALTON electrical tools, WALTON automotive maintenance tools, WALTON fastening tools, WALTON cutting tools, WALTON striking tools, WALTON grinding tools, WALTON original German imports. Customers are welcome to inquire and order.