German SOUDAL tools SOUDAL models SOUDAL prices

SOUDAL tools refer to electrical safety tools, which are various specialized tools and devices designed to prevent accidents such as electric shock, burns, falls, and stumbling, thereby ensuring the personal safety of workers. In power systems, operators must carry and use various safety tools to complete tasks smoothly without causing personal injury. For example, electrical safety equipment is required when inspecting operating electrical equipment, changing operating modes, or performing maintenance and tests; climbing safety equipment is needed during line construction; when working on live electrical equipment or in areas near live equipment, insulating safety tools must be used to prevent electric shock or arc burns. Electrical safety tools can be divided into four categories: personal protective equipment, insulating safety tools, climbing tools, and warning signs.

SOUDAL tool types

1) Frame saw. Also known as a buck saw, it consists of an H-shaped wooden frame, twisted rope, twisting pieces, and a saw blade. The ends of the saw blade are fixed to the frame with knobs, which can also be used to adjust the angle of the blade. After tightening the twisted rope, the blade is taut and ready for use. Frame saws are classified into coarse, medium, and fine types based on blade length and tooth pitch. Coarse saw blades are 650—750mm long, with a tooth pitch of 4—5mm; they are mainly used for cutting thicker wood. Medium saw blades are 550—650mm long, with a tooth pitch of 3—4mm; they are mainly used for cutting thin wood or cutting tenons. Fine saw blades are 450—500mm long, with a tooth pitch of 2—3mm; they are mainly used for cutting finer wood and cutting tenon shoulders. 2) Knife saw. A knife saw mainly consists of a saw edge and a handle, and can be divided into single-sided, double-sided, and backed knife saws. Single-sided knife saws have a blade length of 350mm, with teeth on one side; depending on the function of the teeth, they can be used for rip cutting or crosscutting. Double-sided knife saws have a blade length of 300mm, with teeth on both sides; typically, one side is for rip cutting and the other for crosscutting. Backed knife saws have a blade plate length of 250—300mm; the back of the blade is reinforced with a steel strip, and the teeth are finer, available for both rip and crosscutting. 3) Groove saw. A groove saw consists of a handle and a saw blade, with the blade being approximately 200mm long. It is mainly used for cutting grooves in wood. 4) Panel saw. Also known as a hand saw, it consists of a handle and a saw blade. The blade is approximately 250—750mm long, with a tooth pitch of 3—4mm. Panel saws are mainly used for cutting wider boards. 5) Keyhole saw. The blade is narrow and long, with a pointed tip, and a length of approximately 300—400mm. Keyhole saws are mainly used for cutting small holes and slots. 6) Coping saw. Also known as a fret saw, its construction is similar to that of a frame saw, but the blade is narrower (approximately 10mm), mainly used for cutting arcs and curves. 7) Wire saw. Also known as a bow saw, it is made by bending a bamboo strip into a bow shape, with wire stretched between the two ends. The wire has serrated edges cut into it, using the sharp edges for cutting. The wire is approximately 200—600mm long, and the saw bow is 800—900mm long. Wire saws are mainly used for cutting complex curves and openings.

SOUDAL tool precautions

Large saws are commonly used for wide and thick boards; small saws are used for narrow and thin wood; coarse saws are commonly used for crosscutting; fine saws are used for tenons and shoulders; saws with greater set are used for hardwoods and wet wood, while saws with less set are used for softwoods and dry wood. When using saws, attention must be paid to safe operating methods for each type: 1) Before using a frame saw, adjust the blade angle with the knobs; conventionally, it should form an angle of 45° with the plane of the wooden frame. Tighten the cord with the twisting piece to keep the blade taut and straight. When starting the cut, hold the handle firmly with the right hand and place the left hand at the starting point, pulling and pushing gently a few times. Do not apply excessive force; do not twist the saw left or right during cutting. Apply more pressure on the push stroke and less on the pull stroke, maintaining a uniform rhythm. Hold the part being cut off steady with your hand when nearing the end of the cut. Loosen the blade after use and hang it in a secure location. 2) When using a crosscut saw, apply balanced force with both hands to prevent the saw from drifting toward the side with greater force. Correct any deviation slowly to prevent binding or breaking the blade. 3) When using a wire saw, do not apply excessive force or pull too quickly, to avoid breaking the wire. When pulling the saw, the operator's head must not be positioned above the top of the bow frame, to avoid facial injury if the wire breaks. 4) Regularly check the sharpness of the blade and the stability of the saw frame and handle. Repair blades with dull or uneven teeth promptly. Repair or replace damaged ropes, nuts, knobs, handles, and wooden frames before continuing use.

SOUDAL tool usage

1) Explosion-proof tools provide safety assurance for workers in flammable, explosive, and corrosive environments, enhancing social safety and allowing workers to operate with greater confidence. After daily use, explosion-proof tools require proper maintenance, which is crucial for their service life. Improper maintenance may prevent the tools from serving us effectively for a long time. First, store the tools in a dry place to prevent damage to working components. In daily work, after 20 consecutive strikes, remove surface deposits from the tools, wipe them clean, and then resume use. Do not use them continuously, as prolonged friction may cause overheating and potential damage to the tool products. 2) After use, wipe off surface dirt and deposits, and store in a dry, safe place. 3) Striking tools must not be used for continuous impacts; allow appropriate intervals after every ten strikes, and promptly remove debris adhering to the product before continuing use. 4) Wrenches must not be used with excessive force. Do not extend the lever arm by attaching sleeves or binding other metal rods, and do not use a hammer to tighten fasteners (except for striking wrenches). 5) Cutting-edge tools should be lightly touched against a grinding wheel in a water trough for sharpening. Do not apply excessive force or maintain contact with the grinding wheel for too long. 6) In actual operation with chiseling tools, clear site debris and corrosive oxides from the work surface to prevent third-party impact. Based on the above performance and usage, aluminum-copper alloys are more suitable for atmospheric pressure equipment and environments with less stringent explosion-proof requirements (such as gas stations and small oil depots). Beryllium-copper alloy explosion-proof tools are suitable for applications such as refineries, gas transfer stations, gas production plants, and drilling teams. 7) Remove surface oil stains from all products before use, and refer to the instructions for steel tools.

Weidou Intelligent Technology professionally sells German SOUDAL workpiece clamps, SOUDAL hydraulic tools, SOUDAL power tools, SOUDAL pneumatic tools, SOUDAL hand tools, SOUDAL electronic tools, SOUDAL welding tools, SOUDAL pipe tools, SOUDAL explosion-proof tools, SOUDAL electrical tools, SOUDAL automotive maintenance tools, SOUDAL fastening tools, SOUDAL cutting tools, SOUDAL striking tools, SOUDAL grinding tools, SOUDAL original German imports. Welcome inquiries and orders from users.