German SAINT GOBAIN tools, SAINT GOBAIN models, SAINT GOBAIN prices

SAINT GOBAIN tools utilize electromagnetic technologies such as permanent magnets to assist in mechanical manufacturing processes. They can be categorized into magnetic fixtures, magnetic tools, magnetic molds, and magnetic auxiliary aids. The use of magnetic tools can significantly improve production efficiency and reduce the labor intensity of employees. For some workpieces, clamping is inconvenient during machining and assembly due to their structural characteristics. Simply position the U-shaped iron core vertically on the worktable for processing; at this point, by embedding a magnet in the positioning block of the fixture, the workpiece can be firmly adsorbed onto the worktable equipped with positioning blocks and accurately positioned. This greatly simplifies the fixture structure and improves work efficiency. Some products require welding small parts onto the workpiece; if accurate positioning is not achieved, it not only makes the work inconvenient but also fails to meet requirements.

SAINT GOBAIN tool types

1) Frame saw. Also known as a rack saw, it consists of an I-shaped wooden frame, twisted rope and twist pieces, and a saw blade. Both ends of the saw blade are fixed to the frame with knobs, which can also be used to adjust the angle of the saw blade. After the twisted rope is tightened, the saw blade is taut and ready for use. Frame saws are classified into coarse, medium, and fine types based on saw blade length and tooth pitch. Coarse saw blades are 650—750mm long, with a tooth pitch of 4—5mm; coarse saws are mainly used for sawing thicker lumber. Medium saw blades are 550—650mm long, with a tooth pitch of 3—4mm; medium saws are mainly used for sawing thin lumber or cutting tenons. Fine saw blades are 450—500mm long, with a tooth pitch of 2—3mm; fine saws are mainly used for sawing finer wood and cutting tenon shoulders. 2) Knife saw. A knife saw mainly consists of a saw edge and a saw handle, and can be divided into single-sided, double-sided, and back-backed knife saws. Single-sided knife saws have a blade length of 350mm, with teeth on one side; depending on the function of the teeth, they can be divided into rip cuts and cross cuts. Double-sided knife saws have a blade length of 300mm, with teeth on both sides; generally, one side is for rip cuts and the other for cross cuts. Back-backed knife saws have a blade plate length of 250—300mm; the back of the back-backed knife saw is straightened with a steel strip, and the teeth are finer, available in rip and cross cut types. 3) Groove saw. A groove saw consists of a handle and a saw blade, with the blade being approximately 200mm long. Groove saws are mainly used for cutting grooves in wood. 4) Panel saw. Also known as a hand saw, it consists of a handle and a saw blade, with the blade being approximately 250—750mm long and a tooth pitch of 3—4mm. Panel saws are mainly used for sawing wider boards. 5) Narrow hand saw. The saw blade is narrow and long, with a pointed front end, and a length of approximately 300—400mm. Narrow hand saws are mainly used for sawing narrow holes and slots. 6) Coping saw. Also known as a fret saw, its construction is similar to that of a frame saw, but the saw blade is narrower (approximately 10mm), mainly used for sawing arcs, curves, and other sections. 7) Wire saw. Also known as a bow saw, it is made by bending a bamboo strip into a bow shape and stretching wire across both ends. Saw-tooth-like flying edges are chiseled onto the wire, using the sharp edges of these flying edges for sawing. The wire is approximately 200—600mm long, and the saw bow is 800—900mm long. Wire saws are mainly used for sawing complex curves and cutting holes.

SAINT GOBAIN tool usage

1) Rip cutting method: When sawing, place the wood on a bench. Step on the wood with your right foot, keeping it perpendicular to the cut line. Stand straight with your left foot at a 60° angle to the cut line. Keep your right hand perpendicular to your right knee. It is appropriate for your body to form a 45° angle with the cut line. Lean your upper body forward slightly and allow for slight movement, but do not lean backward or lunge sideways. When sawing, hold the saw with your right hand and place your left thumb against the blade for positioning. Gently pull and push the saw with your right hand (pull first, then push) to create the initial kerf. Once the teeth have penetrated the wood to a depth of approximately 5mm, remove your left hand from the edge of the saw and use it to assist your right hand in lifting and advancing the frame saw. Lift the saw lightly, raising the sawing hand slightly; apply heavier pressure when pushing the saw. Apply force rhythmically using your wrist, elbow, shoulder, and waist simultaneously. This ensures the saw blade advances along the cut line. Otherwise, the edge of the wood after rip cutting will be curved or uneven, or the cross-section of the kerf will be inconsistent. 2) Cross-cutting method: When sawing, place the wood on a bench. Stand behind and to the left of the wood. Hold the wood with your left hand and the saw with your right hand. Step on the wood with your left foot. The pulling and sawing method is the same as for rip cutting. When using a frame saw, the lower end of the blade should tilt forward. For rip sawing, the upper end of the blade should tilt backward at an angle of approximately 75° to 90° (relative to the wood surface). For cross-cutting, the blade should tilt backward at an angle of approximately 30° to 45°. Always ensure the saw blade advances along the line without deviation. The kerf must be straight; avoid swaying the blade left and right, which causes skewing. When the wood is nearly severed, stabilize the offcut with your left hand and slow down the sawing speed. Continue until the wood is completely cut through. Do not leave any material uncut to be broken off by bending or snapping, as this can easily damage the saw blade and cause the wood to split along the grain, compromising quality.

SAINT GOBAIN tool usage

1) When placing the diamond dressing tool head into the holder, be careful not to impact the grinding wheel surface. 2) Do not align the single-point diamond dressing tool head vertically with the center of the grinding wheel; it generally needs to be tilted by 10-15°. 3) Do not "quench" (suddenly cool) a heated dressing tool. During dry dressing, maintain sufficient interval time between two dressings to allow the heated dressing tool to cool. 4) Do not assume the grinding wheel surface has ideal flatness. At the start of dressing, locate the high points on the grinding wheel and perform dressing. 5) If possible, the amount removed from the grinding wheel each time should not exceed 0.001 inches on the radius. Excessive removal can cause premature wear and frequent fracture of the diamond dressing tool head. 6) However, do not remove too little material each time. Grinding wheels used on old or poorly rigid machine tools may not require dressing. 7) Note that you should not stay in one position for too long during dressing. This will polish the grinding wheel surface, generate high temperatures, and damage the diamond dressing tool. Rotate the dressing tool at least once a day. 8) Do not continue to use worn or damaged dressing tools. Adjust or replace them promptly. 9) Do not select excessive removal amounts and too fast lateral feed rates during rough dressing, and then select small removal amounts and slow lateral feed rates during fine dressing. This will quickly damage the diamond dressing tool. If possible, it is recommended to select the same lateral feed rate for both rough and fine dressing.

Weidou Intelligent Technology specializes in selling German SAINT GOBAIN workpiece fixtures, SAINT GOBAIN hydraulic tools, SAINT GOBAIN power tools, SAINT GOBAIN pneumatic tools, SAINT GOBAIN hand tools, SAINT GOBAIN electronic tools, SAINT GOBAIN welding tools, SAINT GOBAIN pipe tools, SAINT GOBAIN explosion-proof tools, SAINT GOBAIN electrical tools, SAINT GOBAIN automotive maintenance tools, SAINT GOBAIN fastening tools, SAINT GOBAIN cutting tools, SAINT GOBAIN striking tools, SAINT GOBAIN grinding tools. SAINT GOBAIN products are original imports from Germany. We welcome inquiries and orders from users.