German MORAVIA tools MORAVIA models MORAVIA prices

MORAVIA tools is a general term for various metal devices manufactured through physical processing such as forging, rolling, and cutting of metals like iron, steel, and aluminum. Hardware tools, classified by product application, can be divided into: tool hardware, construction hardware, daily-use hardware, locks and abrasives, kitchen and bathroom hardware, home hardware, and hardware components. These include various manual, electric, pneumatic, and cutting tools; automotive maintenance tools; agricultural tools; lifting tools; measuring tools; tool machinery; cutting tools; jigs and fixtures; cutters; molds; cutting edges; grinding wheels; drill bits; polishing machines; tool accessories; measuring instruments and cutting edges; painting tools; abrasives and abrasive materials; manual socket wrench sockets; striking open-end wrenches; and striking box-end wrenches.

MORAVIA tool applications and usage

The electric hydraulic oil pump can serve as the hydraulic pump for various hydraulic devices. When equipped with other hydraulic tools, the electric hydraulic oil pump can perform tasks such as lifting, pressing, pipe bending, bar bending, straightening, shearing, assembly, and disassembly. This reduces labor intensity and improves work efficiency. During use, open the air release nut, turn on the switch on the oil collection block, connect the power supply, and attach the quick connector to the quick coupler of the corresponding hydraulic device. Press the power switch; after the motor runs for 1-2 minutes, turn off the switch to set it to the pressure-boosting state. At this point, the output hydraulic oil will perform various tasks, self-pressurizing as the load increases until 63MPA. After work is completed, open the switch to relieve pressure. Once the hydraulic oil has returned, remove the quick connector, tighten the air release nut, unplug the power cord, and close the switch.

MORAVIA tool usage

1) Rip cutting method: When sawing, place the wood on a bench, step on the wood with your right foot perpendicular to the saw line, stand straight with your left foot at an angle of 60° to the saw line, keep your right hand perpendicular to your right knee, and position your body at an angle of approximately 45° to the saw line. Lean forward slightly and move gently, avoiding leaning left or lunging right. When sawing, hold the saw with your right hand and place your left thumb against the blade for positioning. Gently pull and push the saw a few times (pull first, then push) to start the kerf, then remove your left hand from the edge. When the teeth have cut into the wood about 5mm, use your left hand to assist your right hand in lifting and pushing the frame saw. Lift the saw lightly, raising the sawing hand slightly; push the saw with more force, applying simultaneous effort from the wrist, elbow, shoulder, and waist in a rhythmic manner. This ensures the saw blade advances along the saw line. Otherwise, the edge of the wood after rip cutting will be bent and uneven, or the kerf surface will be inconsistent top to bottom. 2) Cross-cutting method: When sawing, place the wood on a bench, stand to the left rear of the wood, hold the wood with your left hand, hold the saw with your right hand, and step on the wood with your left foot. The sawing method is the same as for rip cutting. When using a frame saw, the lower end of the blade should tilt forward. For rip sawing, the upper end of the blade tilts backward at an angle of approximately 75°—90° (angle relative to the wood surface); for cross-cutting, the blade tilts backward at an angle of approximately 30°—45°. Always ensure the saw blade advances along the line without deviation. The kerf must be straight; avoid swaying the blade left and right, which causes skewing. When the wood is nearly severed, stabilize the cutoff piece with your left hand, slow down the sawing speed, and cut completely through the wood. Do not leave any material to snap off or break by hand, as this can damage the saw blade and cause the wood to split along the grain, affecting quality.

MORAVIA tool usage

1) Before use, carefully inspect the tool. The exterior must be undamaged, the switch must operate flexibly without sticking, and the power cord and housing of the power tool must be intact. Use a 500V megohmmeter to measure the insulation resistance between the winding and the housing; the value must not be less than O.5 megohms. See the attached table for insulation resistance values. 2) Handheld power tools with metal housings must have a reliable protective grounding wire. The power cord shall be a multi-core soft rubber-sheathed cable, and the grounding protection wire at both ends must be securely connected. 3) Handheld power tools shall be used by dedicated personnel with appropriate professional knowledge. Strictly adhere to relevant safety operating procedures during use. 4) Before use, check whether the related electrical and mechanical protection devices are intact and functioning normally. Also ensure that rotating parts move flexibly without sticking. 5) When using Class I handheld power tools, users must wear prescribed protective equipment and use qualified protective gear. Take appropriate anti-electric shock safety measures as required, such as installing residual current devices (RCDs) in the power circuit, or having the user wear insulating gloves, insulating shoes, or stand on an insulating mat. When using Class II handheld power tools in damp and confined spaces, install a residual current circuit breaker (RCCB) with an operating current of less than 1.5mA and an operating time of less than or equal to 0.1 seconds. The RCCB must be placed inside the container and monitored by a dedicated person. 6) Occupational hazards of using handheld power tools. Arm vibration disease caused by long-term exposure to hand-transmitted vibration was listed as one of China's statutory occupational diseases as early as 1957, also known as local vibration disease, typically manifested as episodic white finger.

Weidou Intelligent Technology specializes in selling German MORAVIA workholding fixtures, MORAVIA hydraulic tools, MORAVIA power tools, MORAVIA pneumatic tools, MORAVIA manual tools, MORAVIA electronic tools, MORAVIA welding tools, MORAVIA piping tools, MORAVIA explosion-proof tools, MORAVIA electrical power tools, MORAVIA automotive maintenance tools, MORAVIA fastening tools, MORAVIA cutting tools, MORAVIA striking tools, MORAVIA grinding tools. MORAVIA original imports from Germany. Welcome inquiries and orders from customers.