German industra tools industra models industra prices

industra tools refer to electrical safety tools and equipment, which are various specialized tools and devices designed to prevent accidents such as electric shock, burns, falls, and tumbles, thereby ensuring the personal safety of workers. In power systems, to successfully complete tasks without causing personal injury, operators must carry and use various safety tools and equipment. For example, electrical safety tools are required when inspecting operating electrical equipment, changing operating modes, or performing maintenance and tests; climbing safety tools are needed during line construction; when working on live electrical equipment or in areas near live equipment, insulated safety tools and equipment must be used to prevent electric shock or arc burns. Electrical safety tools and equipment can be divided into four categories: personal protective equipment, insulated safety tools and equipment, climbing tools and equipment, and warning signs.

industra tool types

1) Frame saw. Also known as a buck saw, it consists of an H-shaped wooden frame, twisted rope and twist pieces, and a saw blade. Both ends of the saw blade are fixed to the frame with knobs, which can also be used to adjust the angle of the blade. After the twisted rope is tightened, the saw blade is tensioned and ready for use. Frame saws are classified into coarse, medium, and fine types based on blade length and tooth pitch. Coarse saw blades are 650—750mm long, with a tooth pitch of 4—5mm; coarse saws are mainly used for cutting thicker lumber. Medium saw blades are 550—650mm long, with a tooth pitch of 3—4mm; medium saws are mainly used for cutting thin lumber or cutting tenons. Fine saw blades are 450—500mm long, with a tooth pitch of 2—3mm; fine saws are mainly used for cutting finer wood and cutting tenon shoulders. 2) Knife saw. A knife saw mainly consists of two parts: the saw edge and the handle. It can be divided into single-sided, double-sided, and back-backed knife saws. Single-sided knife saws have a blade length of 350mm, with teeth on one side. Depending on the function of the teeth, they can be divided into rip-cut and cross-cut types. Double-sided knife saws have a blade length of 300mm, with teeth on both sides; typically, one side is for rip-cutting and the other for cross-cutting. Back-backed knife saws have a blade plate length of 250—300mm. The back of the back-backed knife saw is reinforced with a steel strip to keep it straight. The teeth are finer, and they are available in rip-cut and cross-cut versions. 3) Groove saw. A groove saw consists of a handle and a saw blade, with the blade being approximately 200mm long. Groove saws are mainly used for cutting grooves in wood. 4) Panel saw. Also known as a hand saw. It consists of a handle and a saw blade, with the blade being approximately 250—750mm long and a tooth pitch of 3—4mm. Panel saws are mainly used for cutting wider boards. 5) Narrow hand saw. The blade is narrow and long, with a pointed tip, and a length of approximately 300—400mm. Narrow hand saws are mainly used for cutting in narrow holes and slots. 6) Keyhole saw. Also known as a compass saw. Its construction is similar to that of a frame saw, but the blade is narrower (approximately 10mm), and it is mainly used for cutting arcs, curves, and similar shapes. 7) Wire saw. Also known as a bow saw. It is made by bending a bamboo strip into a bow shape and stretching a steel wire between the two ends. Saw-tooth-like projections are cut into the steel wire, using their sharp edges for cutting. The steel wire is approximately 200—600mm long, and the saw bow is 800—900mm long. Wire saws are mainly used for cutting complex curves and opening holes.

industra tool usage

1) Rip-cutting method: When sawing, place the wood on a bench, step on the wood with your right foot, keeping it at a right angle to the cutting line. Stand straight with your left foot, forming a 60° angle with the cutting line. Keep your right hand perpendicular to your right knee. Your body should form an angle of approximately 45° with the cutting line, which is suitable. Lean your upper body forward slightly and move it gently, but do not lean left or lunge right. When sawing, hold the saw with your right hand and place your left thumb against the blade for positioning. Gently pull and push the saw a few times with your right hand (pull first, then push) to start the kerf. Then remove your left hand from the edge of the saw. When the teeth have penetrated the wood by about 5mm, use your left hand to help your right hand lift and push the frame saw. Lift the saw lightly, raising the sawing hand slightly. Push the saw with more force, applying simultaneous effort from your wrist, elbow, shoulder, waist, and body in a rhythmic manner. This ensures the saw blade advances along the cutting line. Otherwise, the edge of the wood after rip-cutting will be bent and uneven, or the cut surface will be inconsistent from top to bottom. 2) Cross-cutting method: When sawing, place the wood on a bench. Stand at the rear left of the wood, hold the wood with your left hand, hold the saw with your right hand, and step on the wood with your left foot. The sawing method is the same as for rip-cutting. When using a frame saw for cross-cutting, the lower end of the blade should tilt forward. For rip-sawing, the upper end of the blade tilts backward at an angle of approximately 75°—90° (angle with the wood surface). For cross-sawing, the blade tilts backward at an angle of approximately 30°—45°. Always ensure the saw blade advances along the line without deviation. The cut must be straight; avoid swaying the blade left and right, which causes skewing. When the wood is nearly severed, stabilize the offcut with your left hand, slow down the sawing speed, and cut completely through the wood. Do not leave any material uncut to let it break off or snap it by hand, as this can easily damage the saw blade and cause the wood to split along the grain, affecting quality.

industra tool usage

1) When placing the diamond dressing tool holder into the chuck, be careful not to impact the grinding wheel surface. 2) Do not align the single-point diamond dressing tool head vertically with the center of the grinding wheel; it generally needs to be tilted by 10-15°. 3) Do not "quench" (i.e., suddenly cool) a heated dressing tool. During dry dressing, maintain sufficient intervals between dressing operations to allow the heated dressing tool to cool. 4) Do not assume the grinding wheel surface is ideally flat. At the start of dressing, locate the high points on the grinding wheel and perform dressing. 5) If possible, the amount removed from the grinding wheel during each dressing operation should not exceed 0.001 inches on the radius. Excessive removal can cause premature wear and frequent fracture of the diamond dressing tool head. 6) However, do not remove too little material each time. Grinding wheels used on old or less rigid machine tools may not require dressing. 7) Note that the dressing tool should not remain in one position for too long. This will polish the grinding wheel surface, generate high temperatures, and damage the diamond dressing tool. Rotate the dressing tool at least once a day. 8) Do not continue to use worn or damaged dressing tools. Adjust or replace them promptly. 9) Do not select excessive removal amounts and too fast lateral feed rates during rough dressing, followed by small removal amounts and slow lateral feed rates during finish dressing. This will quickly damage the diamond dressing tool. If possible, it is recommended to use the same lateral feed rate for both rough and finish dressing.

Weidou Intelligent Technology specializes in selling German industra workpiece clamps, industra hydraulic tools, industra power tools, industra pneumatic tools, industra hand tools, industra electronic tools, industra welding tools, industra pipe tools, industra explosion-proof tools, industra electrical tools, industra automotive maintenance tools, industra fastening tools, industra cutting tools, industra striking tools, industra grinding tools, industra original imports from Germany. We welcome inquiries and orders from customers.