German HG6 tools HG6 model HG6 price

HG6 tools integrate hydraulic systems with conventional tools into a unified assembly. They convert powerful hydraulic power into mechanical motions such as reciprocating linear motion, rotary motion, and orbital motion. A complete hydraulic tool system consists of five components: power elements, actuating elements, control elements, auxiliary elements, and hydraulic oil. Hydraulic tools include: hydraulic wrenches, electric pumps dedicated to hydraulic wrenches, hydraulic jacks, hydraulic bolt tensioners, hydraulic flange spreaders, hydraulic nut splitters, hydraulic pullers, etc. Hydraulic tools offer the advantages of high efficiency and convenience. A complete hydraulic tool system consists of five components: power elements, actuating elements, control elements, auxiliary elements, and hydraulic oil.

HG6 tool types

1) Frame saw. Also known as a sash saw, it consists of an I-shaped wooden frame, twisted rope and twist pieces, and a saw blade. Both ends of the saw blade are fixed to the frame with knobs, which can be used to adjust the angle of the blade. After tightening the twisted rope, the saw blade is taut and ready for use. Frame saws are classified into coarse, medium, and fine types based on blade length and tooth pitch. Coarse saw blades are 650—750mm long, with a tooth pitch of 4—5mm; coarse saws are mainly used for cutting thicker lumber. Medium saw blades are 550—650mm long, with a tooth pitch of 3—4mm; medium saws are mainly used for cutting thin lumber or cutting tenons. Fine saw blades are 450—500mm long, with a tooth pitch of 2—3mm; fine saws are mainly used for cutting finer wood and cutting tenon shoulders. 2) Knife saw. A knife saw mainly consists of two parts: the saw edge and the handle. It can be classified into single-sided, double-sided, and backed knife saws. Single-sided knife saws have a blade length of 350mm, with teeth on one side; depending on the function of the teeth, they can be divided into rip-cut and cross-cut types. Double-sided knife saws have a blade length of 300mm, with teeth on both sides; typically, one side is for rip-cutting and the other for cross-cutting. Backed knife saws have a blade plate length of 250—300mm; the back of the backed knife saw is reinforced with a steel strip, and the teeth are finer, available in rip-cut and cross-cut versions. 3) Groove saw. A groove saw consists of a handle and a saw blade, with the blade being approximately 200mm long. Groove saws are mainly used for cutting grooves in wood. 4) Panel saw. Also known as a hand saw. It consists of a handle and a saw blade, with the blade being approximately 250—750mm long and a tooth pitch of 3—4mm. Panel saws are mainly used for cutting wider boards. 5) Narrow hand saw. The blade is narrow and long, with a pointed tip, and a length of approximately 300—400mm. Narrow hand saws are mainly used for cutting narrow holes and slots. 6) Keyhole saw. Also known as a compass saw, its construction is similar to that of a frame saw, but the blade is narrower (approximately 10mm), mainly used for cutting arcs, curves, and similar shapes. 7) Wire saw. Also known as a bow saw, it is made by bending a bamboo strip into a bow shape, with wire stretched between the two ends. Saw-tooth-like projections are cut into the wire, using the sharp edges of these projections for cutting. The wire is approximately 200—600mm long, and the saw bow is 800—900mm long. Wire saws are mainly used for cutting complex curves and opening holes.

HG6 tool maintenance

1) Correct air supply system: The intake pressure at the tool inlet (not the compressor outlet pressure) is generally 90PSIG (6.2Kg/cm^2). Pressure that is too high or too low will impair tool performance and service life. The intake air must contain sufficient lubricating oil to ensure adequate lubrication of the pneumatic motor inside the tool (place a white paper at the tool exhaust to check for oil stains; the presence of oil stains is normal). The intake air must be free of moisture; it is inappropriate if the compressed air has not passed through an air dryer. 2) Do not arbitrarily disassemble tool parts before operation, as this may compromise operator safety and cause tool damage. 3) If the tool has minor faults or fails to achieve its original function after use, do not continue using it; inspect it immediately. 4) Regularly (approximately once a week) inspect and maintain the tool, adding grease (Grease) to rotating parts such as bearings, and adding oil (Oil) to the pneumatic motor. 5) When using various tools, strictly adhere to all safety regulations and operating instructions. 6) Select appropriate tools for the job; tools that are too large can easily cause work-related injuries, while tools that are too small can easily lead to tool damage.

HG6 tool usage

1) When placing the diamond dressing tool holder into the chuck, take care not to impact the grinding wheel surface. 2) Do not align the single-point diamond dressing tool holder vertically with the center of the grinding wheel; it generally needs to be tilted 10-15°. 3) Do not "quench" (i.e., suddenly cool) a heated dressing tool. During dry dressing, maintain sufficient interval time between dressings to allow the heated dressing tool to cool. 4) Do not assume the grinding wheel surface is ideally flat. At the start of dressing, locate the high points on the grinding wheel and proceed with dressing. 5) If possible, the amount removed from the grinding wheel during each dressing should not exceed 0.001 inches on the wheel radius. Excessive removal can cause premature wear and frequent fracture of the diamond dressing tool holder. 6) However, do not remove too little material each time. Grinding wheels used on old or less rigid machine tools may not require dressing. 7) Note that the dressing tool should not remain in one position for too long. This will polish the grinding wheel surface, generate high temperatures, and damage the diamond dressing tool. Rotate the dressing tool at least once daily. 8) Do not continue to use worn or damaged dressing tools. Adjust or replace them promptly. 9) Do not select excessive removal amounts and fast lateral feed rates during rough dressing, followed by small removal amounts and slow lateral feed rates during finish dressing. This will quickly damage the diamond dressing tool. If possible, it is recommended to use the same lateral feed rate for both rough and finish dressing.

Weidou Intelligent Technology specializes in selling German HG6 workholding fixtures, HG6 hydraulic tools, HG6 power tools, HG6 pneumatic tools, HG6 hand tools, HG6 electronic tools, HG6 welding tools, HG6 piping tools, HG6 explosion-proof tools, HG6 electrical power tools, HG6 automotive maintenance tools, HG6 fastening tools, HG6 cutting tools, HG6 striking tools, HG6 grinding tools, HG6 original German imports. Customers are welcome to inquire and place orders.