German FACOM tools FACOM models FACOM prices

FACOM tools integrate hydraulic systems with conventional tools into a unified whole. They convert powerful hydraulic power into mechanical motions such as reciprocating linear motion, rotary motion, and cycloidal motion. A complete hydraulic tool system consists of five parts: power elements, actuating elements, control elements, auxiliary elements, and hydraulic oil. Hydraulic tools include: hydraulic wrenches, electric pumps dedicated to hydraulic wrenches, hydraulic jacks, hydraulic bolt tensioners, hydraulic flange spreaders, hydraulic nut splitters, hydraulic pullers, etc. Hydraulic tools offer the advantages of high efficiency and convenience. A complete hydraulic tool system consists of five parts: power elements, actuating elements, control elements, auxiliary elements, and hydraulic oil.

FACOM tool features

1) Air is easily accessible, operates at low pressure, and used air can be vented locally without requiring return pipelines. 2) Air has low viscosity and minimal flow resistance loss, facilitating centralized air supply and long-distance transmission. 3) Pneumatic actuators achieve high movement speeds. 4) Pneumatic systems have strong environmental adaptability, operating reliably in wide temperature ranges, humid and dusty conditions; minor leaks do not pollute the environment, there is no risk of fire or explosion, ensuring safe use. 5) Simple structure, easy maintenance, and low cost. 6) Long service life of pneumatic components. 7) Pneumatic components have lower output force compared to hydraulic systems, faster motion, strong adaptability, and can operate in harsh environments such as flammable, explosive, dusty, humid, and impact-prone areas without polluting the environment; they offer long service life, simple construction, easy maintenance, and low price.

FACOM tool usage

1) Rip cutting method: When sawing, place the wood on a bench, step on the wood with your right foot perpendicular to the cut line, stand straight with your left foot at an angle of 60° to the cut line, keep your right hand vertical to your right knee, and position your body at approximately 45° to the cut line. Lean your upper body slightly forward with slight movement, but avoid leaning left or lunging right. Hold the saw with your right hand, and use your left thumb against the blade for positioning. Gently pull and push the saw a few times (pull first, then push) to start the kerf, then remove your left hand from the edge. When the teeth have penetrated about 5mm into the wood, use your left hand to assist your right hand in lifting and pushing the frame saw. Lift the saw lightly, raising the sawing hand slightly; push the saw with more force, applying simultaneous effort from wrist, elbow, shoulder, and waist in a rhythmic manner. This ensures the saw blade follows the cut line. Otherwise, the edge of the rip-cut wood will be curved or uneven, or the kerf surface will be inconsistent top-to-bottom. 2) Cross-cutting method: When sawing, place the wood on a bench, stand to the rear left of the wood, hold the wood with your left hand, hold the saw with your right hand, and step on the wood with your left foot. The sawing method is the same as for rip cutting. When using a frame saw, the lower end of the blade should tilt forward. For rip sawing, the upper end of the blade tilts backward at an angle of approximately 75°–90° (relative to the wood surface); for cross-cutting, the blade tilts backward at an angle of approximately 30°–45°. Always ensure the blade follows the line without deviation. Keep the kerf straight; avoid lateral swinging of the blade that causes skewing. When the wood is nearly severed, stabilize the offcut with your left hand, slow down the sawing speed, and cut completely through. Do not leave any material to snap off or break by hand, as this can damage the blade and cause the wood to split along the grain, affecting quality.

FACOM tool usage

1) When placing the diamond dressing tool holder into the chuck, avoid impacting the grinding wheel surface. 2) Do not align a single-point diamond dressing tool vertically with the center of the grinding wheel; generally, it should be tilted 10-15°. 3) Do not "quench" (suddenly cool) a heated dressing tool. During dry dressing, maintain sufficient interval between dressings to allow the heated tool to cool. 4) Do not assume the grinding wheel surface is ideally flat. At the start of dressing, locate the high points on the wheel and proceed with dressing. 5) If possible, the stock removal per dressing should not exceed 0.001 inches on the wheel radius. Excessive removal causes premature wear and frequent fracture of the diamond dressing tool. 6) However, do not remove too little stock each time. Grinding wheels used on old or less rigid machines may not require dressing. 7) Avoid dwelling too long at one position during dressing, as this polishes the wheel surface, generates high temperatures, and damages the diamond dressing tool. Rotate the dressing tool at least once daily. 8) Do not continue using worn or damaged dressing tools. Adjust or replace them promptly. 9) Do not select excessive stock removal and fast traverse speeds for rough dressing, followed by small stock removal and slow traverse speeds for finish dressing, as this rapidly damages the diamond dressing tool. If possible, use the same traverse speed for both rough and finish dressing.

Weidou Intelligent Technology specializes in selling German FACOM workholding fixtures, FACOM hydraulic tools, FACOM power tools, FACOM pneumatic tools, FACOM hand tools, FACOM electronic tools, FACOM welding tools, FACOM pipe tools, FACOM explosion-proof tools, FACOM electrical tools, FACOM automotive maintenance tools, FACOM fastening tools, FACOM cutting tools, FACOM striking tools, FACOM grinding tools. All FACOM products are original imports from Germany. Customers are welcome to inquire and order.