German CIMCOOL tools CIMCOOL models CIMCOOL prices

CIMCOOL tools refer to electrical safety tools, which are various specialized tools and devices designed to prevent accidents such as electric shock, burns, falls, and stumbling, thereby ensuring the personal safety of workers. In power systems, to complete tasks smoothly without personal injury, operators must carry and use various safety tools. For example, electrical safety equipment is required when inspecting operating electrical equipment, changing operating modes, or performing maintenance and tests; climbing safety equipment is needed during line construction; when working on live electrical equipment or in areas near live equipment, insulated safety tools must be used to prevent electric shock or arc burns. Electrical safety tools can be divided into four categories: personal protective equipment, insulated safety tools, climbing tools, and warning signs.

CIMCOOL tool types

1) Frame saw. Also known as a buck saw, it consists of an H-shaped wooden frame, twisted rope and toggle, saw blade, etc. The two ends of the saw blade are fixed to the frame with knobs, which can also be used to adjust the angle of the blade. After tightening the twisted rope, the blade is taut and ready for use. Frame saws are classified into coarse, medium, and fine types based on blade length and tooth pitch. Coarse saw blades are 650—750mm long, with a tooth pitch of 4—5mm; they are mainly used for sawing thicker wood. Medium saw blades are 550—650mm long, with a tooth pitch of 3—4mm; they are mainly used for sawing thin wood or cutting tenons. Fine saw blades are 450—500mm long, with a tooth pitch of 2—3mm; they are mainly used for sawing finer wood and cutting tenon shoulders. 2) Knife saw. A knife saw mainly consists of a saw edge and a handle, and can be divided into single-sided, double-sided, and backed knife saws. Single-sided knife saws have a blade length of 350mm, with teeth on one side; depending on the function of the teeth, they can be divided into rip-cut and cross-cut types. Double-sided knife saws have a blade length of 300mm, with teeth on both sides; typically, one side is for rip-cutting and the other for cross-cutting. Backed knife saws have a blade plate length of 250—300mm; the back of the blade is reinforced with a steel strip, and the teeth are finer, available in rip-cut and cross-cut versions. 3) Groove saw. A groove saw consists of a handle and a saw blade, with the blade being approximately 200mm long. It is mainly used for cutting grooves in wood. 4) Panel saw. Also known as a hand saw, it consists of a handle and a saw blade, with the blade being approximately 250—750mm long and a tooth pitch of 3—4mm. Panel saws are mainly used for sawing wider wooden boards. 5) Narrow hand saw. The blade is narrow and long, with a pointed front end, and a length of approximately 300—400mm. Narrow hand saws are mainly used for sawing narrow holes and slots. 6) Coping saw. Also known as a fret saw, its structure is similar to that of a frame saw, but the blade is narrower (approximately 10mm), mainly used for sawing arcs and curves. 7) Wire saw. Also known as a bow saw, it is made by bending a bamboo strip into a bow shape, with wire stretched between the two ends. The wire has serrated edges cut into it, using the sharp edges for sawing. The wire is approximately 200—600mm long, and the saw bow is 800—900mm long. Wire saws are mainly used for sawing complex curves and cutting holes.

CIMCOOL tool usage

1) Rip-cutting method: When sawing, place the wood on a bench, step on the wood with your right foot, positioning it at a right angle to the cutting line. Stand straight with your left foot, forming a 60° angle with the cutting line. Keep your right hand perpendicular to your right knee. Your body should form an angle of approximately 45° with the cutting line. Lean forward slightly and move naturally, but do not lean left or lunge right. When sawing, hold the saw with your right hand and place your left thumb against the blade for positioning. Gently pull and push the saw a few times with your right hand (pull first, then push) to start the kerf. Then remove your left hand from the blade edge. When the teeth have penetrated the wood by about 5mm, use your left hand to assist your right hand in lifting and pushing the frame saw. Lift the saw lightly, raising the sawing hand slightly; push the saw with more force, applying simultaneous effort from the wrist, elbow, shoulder, and waist in a rhythmic manner. This ensures the blade advances along the cutting line. Otherwise, the edge of the wood after rip-cutting may be bent or uneven, or the cut surface may be inconsistent top-to-bottom. 2) Cross-cutting method: When sawing, place the wood on a bench. Stand to the left rear of the wood, hold the wood with your left hand, hold the saw with your right hand, and step on the wood with your left foot. The sawing motion is the same as for rip-cutting. When using a frame saw, the lower end of the blade should tilt forward. For rip-sawing, the upper end of the blade tilts backward at an angle of approximately 75°—90° (relative to the wood surface). For cross-sawing, the blade tilts backward at an angle of approximately 30°—45°. Always ensure the blade advances along the line without deviation. The cut must be straight; avoid swaying the blade left and right, which causes skewing. When the wood is nearly severed, stabilize the offcut with your left hand, slow down the sawing speed, and cut completely through the wood. Do not leave any material to break off or snap by hand, as this can damage the blade and cause the wood to split along the grain, affecting quality.

CIMCOOL tool usage

1) When placing the diamond dressing tool holder into the chuck, be careful not to impact the grinding wheel surface. 2) Do not align a single-point diamond dressing tool vertically with the center of the grinding wheel; it generally needs to be tilted by 10-15°. 3) Do not "quench" (i.e., suddenly cool) a heated dressing tool. During dry dressing, maintain sufficient interval time between dressings to allow the heated tool to cool. 4) Do not assume the grinding wheel surface is ideally flat. At the start of dressing, locate the high points on the wheel and proceed with dressing. 5) If possible, the amount removed from the grinding wheel per dressing should not exceed 0.001 inches on the radius. Excessive removal can cause premature wear and frequent fracture of the diamond dressing tool. 6) However, do not remove too little material each time. Grinding wheels used on old or less rigid machines may not require dressing. 7) Note that the dressing tool should not remain in one position for too long. This will polish the wheel surface, generate high temperatures, and damage the diamond dressing tool. Rotate the dressing tool at least once daily. 8) Do not continue to use worn or damaged dressing tools. Adjust or replace them promptly. 9) Do not select excessive removal amounts and fast lateral feed rates during rough dressing, followed by small removal amounts and slow lateral feed rates during finish dressing. This will quickly damage the diamond dressing tool. If possible, it is recommended to use the same lateral feed rate for both rough and finish dressing.

Weidou Intelligent Technology specializes in selling German CIMCOOL workholding fixtures, CIMCOOL hydraulic tools, CIMCOOL power tools, CIMCOOL pneumatic tools, CIMCOOL hand tools, CIMCOOL electronic tools, CIMCOOL welding tools, CIMCOOL pipe tools, CIMCOOL explosion-proof tools, CIMCOOL electrical tools, CIMCOOL automotive maintenance tools, CIMCOOL fastening tools, CIMCOOL cutting tools, CIMCOOL striking tools, CIMCOOL grinding tools. All CIMCOOL products are original imports from Germany. Customers are welcome to inquire and order.