German atlantic tools atlantic models atlantic prices

atlantic tools refer to the general term for various metal devices manufactured through physical processing such as forging, rolling, and cutting of metals like iron, steel, and aluminum. Hardware tools, classified by product application, can be divided into: tool hardware, construction hardware, daily-use hardware, locks and abrasives, kitchen and bathroom hardware, home hardware, and hardware components. These include various manual, electric, pneumatic, and cutting tools; automotive maintenance tools; agricultural tools; lifting tools; measuring tools; tool machinery; cutting tools; jigs and fixtures; cutters; molds; cutting edges; grinding wheels; drill bits; polishing machines; tool accessories; measuring instruments and cutting edges; painting tools; abrasives and grinding materials; manual socket wrench sockets; striking open-end wrenches; and striking box-end wrenches.

atlantic tool applications and usage

The electric hydraulic oil pump can serve as the hydraulic pump for various hydraulic equipment. When equipped with other hydraulic tools, the electric hydraulic oil pump can perform tasks such as lifting, pressing, pipe bending, bar bending, straightening, shearing, assembly, and disassembly. It reduces labor intensity and improves work efficiency. During use, open the air release nut, turn on the switch on the oil collection block, connect the power supply, and attach the quick connector to the quick coupling on the corresponding hydraulic equipment. Press the power switch; after the motor runs for 1-2 minutes, turn off the switch to set it to the pressure-boosting state. At this point, the output hydraulic oil will perform various tasks, self-pressurizing as the load increases until reaching 63MPA. After work is completed, open the switch to relieve pressure. Once the hydraulic oil has returned, remove the quick connector, tighten the air release nut, unplug the power cord, and close the switch.

atlantic tool usage

1) Rip cutting method: When sawing, place the wood on a bench. Step on the wood with your right foot, keeping it perpendicular to the cutting line. Stand straight with your left foot at an angle of 60° to the cutting line. Keep your right hand perpendicular to your right knee. Your body should form an angle of approximately 45° with the cutting line. Lean forward slightly and move naturally, but do not lean left or lunge right. When sawing, hold the saw with your right hand and place your left thumb against the blade for positioning. Gently pull and push the saw a few times with your right hand (pull first, then push) to start the kerf. Then remove your left hand from the edge of the saw. When the teeth have cut into the wood about 5mm, use your left hand to assist your right hand in lifting and pushing the frame saw. Lift the saw lightly, raising the sawing hand slightly; push the saw with more force, applying simultaneous effort from the wrist, elbow, shoulder, waist, and body in a rhythmic manner. This ensures the saw blade advances along the cutting line. Otherwise, the edge of the wood after rip cutting will be bent and uneven, or the cross-section of the kerf will be inconsistent top to bottom. 2) Cross-cutting method: When sawing, place the wood on a bench. Stand behind and to the left of the wood. Hold the wood with your left hand and the saw with your right hand. Step on the wood with your left foot. The sawing motion is the same as in rip cutting. When using a frame saw, the lower end of the blade should tilt forward. For rip sawing, the upper end of the blade tilts backward at an angle of approximately 75° to 90° (angle relative to the wood surface). For cross-cutting, the blade tilts backward at an angle of approximately 30° to 45°. Always ensure the saw blade advances along the line without deviation. The kerf must be straight; avoid swaying the blade left and right, which causes skewing. When the wood is nearly severed, stabilize the cutoff piece with your left hand and slow down the sawing speed. Saw completely through the wood; do not leave any material to snap off or break by hand, as this can damage the saw blade and cause the wood to split along the grain, affecting quality.

atlantic tool usage

1) Before use, carefully inspect the tool. Ensure there is no external damage, the switch operates flexibly without sticking, and the power cord and housing of the electric tool are intact. Use a 500V megohmmeter to measure the insulation resistance between the winding and the housing; it must not be less than O.5 megohms. See the attached table for insulation resistance values. 2) Handheld electric tools with metal housings must have a reliable protective grounding wire. The power cord shall be a multi-core soft rubber-sheathed cable, and the grounding protection wire at both ends must be securely connected. 3) Handheld electric tools should be used by dedicated personnel with appropriate professional knowledge. Strictly adhere to relevant safety operating procedures during use. 4) Before use, check whether the related electrical and mechanical protection devices are intact and functioning normally. Also ensure that rotating parts move flexibly without sticking. 5) When using Class I handheld electric tools, users must wear prescribed protective equipment and use qualified protective gear. Take corresponding anti-electric shock safety measures as required, such as installing residual current devices (RCDs) in the power circuit, or having the user wear insulating gloves, insulating shoes, or stand on an insulating mat. When using Class II handheld electric tools in damp and confined spaces, install a residual current circuit breaker (RCCB) with an operating current of less than 1.5mA and an operating time of less than or equal to 0.1 seconds. The RCCB should be placed inside the container and monitored by a dedicated person. 6) Occupational hazards of using handheld electric tools. Arm vibration disease caused by long-term exposure to hand-transmitted vibration was listed as one of China's statutory occupational diseases as early as 1957, also known as local vibration disease, typically manifesting as episodic white finger.

Weidou Intelligent Technology specializes in selling German atlantic workholding fixtures, atlantic hydraulic tools, atlantic electric tools, atlantic pneumatic tools, atlantic manual tools, atlantic electronic tools, atlantic welding tools, atlantic piping tools, atlantic explosion-proof tools, atlantic electrical power tools, atlantic automotive maintenance tools, atlantic fastening tools, atlantic cutting tools, atlantic striking tools, atlantic grinding tools. atlantic original imports from Germany. Welcome inquiries and orders from customers.