German agrar industrie service seals agrar industrie service models agrar industrie service prices

agrar industrie service seals are a type of friction seal or stuffing box used to prevent liquid leakage between the shaft and bearings of compressors or other fluid handling equipment. They are also sealing devices installed to prevent leakage at the pump shaft and housing. Common types of shaft seals include packing seals, mechanical seals, and power seals. The shaft seal of a reciprocating pump is typically a packing seal. When transporting media where leakage is not permitted, a diaphragm reciprocating pump can be used. The shaft seals of rotary pumps (including vane pumps, rotor pumps, etc.) mainly consist of packing seals, mechanical seals, and power seals.

Function of agrar industrie service seals

Prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump. Although the shaft seal occupies a small space in the pump, the normal operation of the pump is closely related to the shaft seal. If the shaft seal is improperly selected, it will not only require frequent maintenance during operation and cause significant loss of the transported liquid, but may also cause fires, explosions, and poisoning accidents due to the leakage of flammable, explosive, and toxic liquids, with unimaginable consequences. Therefore, the shaft seal structure must be reasonably selected to ensure the safe operation of the pump. 1) Since the pressure inside the cylinder is not equal to the external atmospheric pressure, steam inside the cylinder or air outside the cylinder will inevitably leak out or in along the radial gap between the main shaft and the cylinder, causing working medium loss, worsening the operating environment, and heating the shaft journal or allowing steam to enter the bearing chamber, causing oil deterioration. Leaking air also destroys the vacuum, thereby increasing the pumping load. These factors will reduce the efficiency of the unit. Therefore, shaft seals are installed at both ends of the cylinder where the rotor passes through. This type of shaft seal is called an end shaft seal, abbreviated as shaft seal. High-pressure shaft seals are used to prevent steam from leaking out of the cylinder, and low-pressure shaft seals are used to prevent air from leaking into the cylinder. 2) During turbine operation, a portion of the steam will inevitably leak from the shaft end to the atmosphere, causing loss of working medium and heat, and also affecting the working environment of the turbogenerator. If the adjustment is improper and the steam leakage is excessive, it will also cause the temperature of the bearings near the shaft seal to rise or cause water to enter the bearing oil. For this reason, shaft seal heaters are installed in various units to recover and utilize the shaft seal steam leakage from the turbine. 3) Prevent steam inside the cylinder and valve stem leakage from leaking outward, polluting the turbine room environment and bearing lubricating oil quality. Prevent high-temperature steam from flowing over the turbine main shaft during normal unit operation, causing it to heat up and thus causing bearing overheating. Prevent air from leaking into the vacuum part of the cylinder. Ensure the vacuum effect and degree of the condenser during unit startup. Recover shaft seal and valve stem leakage to reduce working medium and energy losses. 4) During turbine tripping shutdown and the entire hot shutdown process where the condenser needs to maintain a vacuum, prevent air from leaking into the turbine, which would accelerate internal cooling of the turbine and cause main shaft bending.

agrar industrie service seal replacement steps

1) Remove the main pulley (belt drive) and remove the key pin; 2) Use a pin puller to remove the locating pins of the shaft seal end cover; 3) Remove the fixing screws of the shaft seal end cover; 4) Use a circular external puller to remove the shaft sleeve (if no puller is available, cut a slot in the shaft sleeve with a cutting machine and knock it down with a chisel, taking care to block sand with something to prevent it from getting into the screw rod); 5) Remove the old shaft seal; 6) Clean the shaft seal end cover and bearing positions, then clean with 755; 7) Apply 638 adhesive to the shaft seal installation position, then carefully install the shaft seal; take care not to damage the rubber lip; you can apply a little oil or high-temperature grease to the rubber surface of the shaft seal; 8) After cleaning the shaft sleeve position, reinstall and fix the end cover securely (you can wrap a layer of thick glossy paper around the shaft to prevent the shaft seal lip from accidentally touching the keyway during end cover installation); 9) Clean the new shaft sleeve and installation position, apply fixing adhesive 638 to the inner circle of the shaft sleeve. Cold fit: Use a force bar to evenly knock the shaft sleeve in, using an outer ring of the same size outside the new shaft sleeve to cushion the knocking to avoid damaging the shaft sleeve. Hot fit: Clean the inside of the shaft sleeve thoroughly, ensuring no oil is present. Apply a ring of 638 adhesive to the shaft journal before the shaft seal, heat the shaft sleeve to 110 degrees, and install it. (Note: Push the shaft sleeve to the edge of the shaft seal, pause briefly. Wait for the temperature to drop before pushing it into the shaft seal position; 10) Install the pulley or coupling, correct the parallelism or centerline, and manually reverse the headstock to allow lubricating oil to return to the front bearing and shaft seal.

agrar industrie service seal installation and shutdown

1) Before starting, keep the seal chamber filled with liquid. When transporting solidifying media, use steam to heat the seal chamber to melt the medium. Manual rotation must be performed before starting to prevent sudden startup from causing the soft ring to shatter. 2) For mechanical seals utilizing an external pump sealing oil system, start the sealing oil system first. Stop the sealing oil system last after shutdown. 3) After stopping a hot oil pump, do not immediately stop the cooling water for the sealing oil chamber and face seal. Wait until the oil temperature at the face seal drops below 80 degrees before stopping the cooling water to avoid damaging the seal parts.

Weidou Intelligent Technology specializes in selling German agrar industrie service seals, agrar industrie service sealing rings, agrar industrie service sealing strips, agrar industrie service pipe seals, agrar industrie service cable seals, agrar industrie service rubber seals, agrar industrie service mechanical seals, agrar industrie service gaskets, agrar industrie service oil seals, agrar industrie service shaft seals, agrar industrie service metal seals, agrar industrie service high-pressure seals, agrar industrie service spiral seals, agrar industrie service centrifugal seals, agrar industrie service sealing rings, agrar industrie service original imports from Germany. Welcome customers to inquire and order.