German Duesterloh Fluidtechnik seals, Duesterloh Fluidtechnik models, Duesterloh Fluidtechnik prices

Duesterloh Fluidtechnik seals refer to devices that prevent fluid leakage, formed by at least one pair of end faces perpendicular to the rotation axis maintaining contact and sliding relative to each other under the action of fluid pressure and the elastic force (or magnetic force) of the compensation mechanism, in conjunction with auxiliary seals. When the auxiliary seal of the compensation ring is a metal bellows, it is called a bellows mechanical seal. There are mainly the following four types of components. a. Main sealing elements: rotating ring and stationary ring. b. Auxiliary sealing elements: O-rings. c. Clamping elements: springs, thrust rings. d. Drive elements: spring seat and keys or fixing screws.

Duesterloh Fluidtechnik seal classification

Oil seals are generally divided into single-piece types and assembled types. The assembled type allows free combination of the cage and lip material, and is generally used for special oil seals. Oil seals can be categorized into various forms and names based on their sealing function, characteristics, structural type, operating state, and sealing mechanism. However, conventionally, rotary shaft lip seals are referred to as oil seals, while sealing elements used for static seals and dynamic seals (generally reciprocating motion) are called seals. The representative form of an oil seal is the TC oil seal, which is a double-lip oil seal with a self-tightening spring fully encapsulated in rubber. The term oil seal commonly refers to this type of tc caged oil seal.

Duesterloh Fluidtechnik seal materials

Common materials for oil seals include: Nitrile rubber, Fluorocarbon rubber, Silicone rubber, Acrylate rubber, Polyurethane, Polytetrafluoroethylene, etc. 1) Nitrile rubber (NBR): It has good heat and wear resistance, and is resistant to various lubricating oils, greases, and oil-gas mixtures. The applicable temperature range is -30~120 degrees Celsius. However, it cannot be used in phosphate ester hydraulic fluids and gear oils containing extreme pressure additives. It performs stably in gasoline and mineral oils with low aniline points. 2) Polyacrylate rubber (ACM): It has superior oil and heat resistance, wear resistance, ozone resistance, and UV radiation resistance. It is especially resistant to lubricating oils, gear oils, motor oils, engine oils, and petroleum-based hydraulic fluids containing extreme pressure agents. It is suitable for operation in the range of -30~150 degrees Celsius. 3) Fluorocarbon rubber: It offers aging resistance, heat resistance, and oil resistance. It is suitable for almost all lubricating oils, fuel oils, and gasoline. It does not harden easily in oils containing extreme pressure additives. However, its cold resistance and high-temperature wear resistance are poor, and it has significant permanent compression deformation. It is suitable for temperatures from -20~250 degrees Celsius. 4) Silicone rubber: It has outstanding high and low-temperature resistance. It can be used long-term at 150 degrees Celsius without performance change; it can be used continuously at 200 for 10000h. It maintains its unique elasticity, ozone resistance, and weather resistance within the working temperature range of -70~260. 5) Polytetrafluoroethylene (PTFE): It has outstanding chemical stability, thermal stability, friction reduction, and self-lubrication. Its decomposition temperature is above 400. Therefore, it can operate normally in the temperature range of -200~300 degrees Celsius. Except for free fluorine and alkali metals, it has excellent corrosion resistance to chemicals, solvents, hydroxides, and acids. Nitrile rubber and fluorocarbon rubber are widely used oil seal materials. The former is low-cost, while the latter offers significant improvements in temperature resistance and sealing performance but is more expensive. It still retains some common disadvantages of ordinary rubber materials, such as poor wear resistance, short service life, and high sensitivity to shaft eccentricity, so leakage phenomena remain relatively common. PTFE oil seals are high-tech products and represent the future direction of oil seal development [2]. When selecting oil seal materials, one must consider the material's compatibility with the working medium, adaptability to the working temperature range, and the lip's ability to follow the high-speed rotation of the shaft. Generally, the temperature of the oil seal lip is 20~50℃ higher than the working medium temperature during operation, which should be noted when selecting materials. The operating range of an oil seal depends on the material used: for Nitrile rubber (NBR), it is -40~120℃; for Acrylate rubber (ACM), it is -30~180℃; for Fluorocarbon rubber (FPM), it is -25~300℃.

Duesterloh Fluidtechnik seal troubleshooting

1) Main factors causing oil seal leakage: Poor sealing of the oil seal is the primary factor causing leakage. When the shaft wears and forms grooves, even replacing it with a new oil seal may not achieve proper sealing. This is due to reduced contact pressure between the oil seal lip and the shaft, resulting in insufficient interference between the oil seal lip diameter and the shaft diameter after installation. Taking the crankshaft oil seal of the S195 diesel engine as an example, the main reasons for poor sealing are analyzed as follows: (1) Poor manufacturing quality of the oil seal; (2) Poor quality of the shaft or bearing; (3) Improper use and maintenance; (4) Improper installation; (5) Improper storage, leading to adverse effects from environmental contamination. 2) Countermeasures for leakage due to poor oil seal sealing: Acquire basic knowledge to identify counterfeit and inferior products, and purchase high-quality, standard-compliant oil seals. During installation, if the outer surface of the shaft diameter has low roughness or defects such as rust spots, corrosion, or burrs, polish it smooth with fine sandpaper or an oil stone. Apply clean engine oil or lubricating grease to the oil seal lip or the corresponding position on the shaft diameter. Apply sealant to the outer ring of the oil seal. Wrap the keyway area on the shaft with hard paper to avoid scratching the oil seal lip. Use a special tool to rotate and press the oil seal inward. Never hammer or force it, to prevent deformation of the oil seal or breakage of the spring, which would cause failure. If lip flipping, spring detachment, or oil seal skewing occurs, it must be removed and reinstalled. Note: Do not arbitrarily tighten the inner spring when the shaft diameter is not worn and the oil seal spring tension is sufficient. Oil seals used in machinery generally operate under harsh conditions, with large ambient temperature differences, abundant dust, and frequent vibration, causing constantly changing stress conditions on components. Therefore, frequent inspection, maintenance, and upkeep are required. If the shaft diameter and bearing are severely worn, or if the oil seal rubber is aging or the spring has failed, repair and replace the corresponding parts promptly. Troubleshoot abnormal heating of components or assemblies immediately. Avoid overspeeding and overloading the machinery to prevent increased temperature at the oil seal lip, rubber aging, and premature lip wear. Regularly check the engine oil level. If the engine oil contains excessive impurities, such as alloy powder or metal iron filings, completely replace it with new oil. The brand and quality of the replacement oil must meet seasonal requirements. It is recommended to add Metra Super Sealant & Lubricant to the engine oil. It is an excellent gearbox additive that forms an inert material film on components, which can reduce oil seal leakage, extend the service life of oil seal gears, and reduce gearbox noise. The use of this Metra super sealant lubricant will not contaminate or degrade the oil.

Weidou Intelligent Technology specializes in selling German Duesterloh Fluidtechnik seals, Duesterloh Fluidtechnik O-rings, Duesterloh Fluidtechnik sealing strips, Duesterloh Fluidtechnik pipe seals, Duesterloh Fluidtechnik cable seals, Duesterloh Fluidtechnik rubber seals, Duesterloh Fluidtechnik mechanical seals, Duesterloh Fluidtechnik gaskets, Duesterloh Fluidtechnik oil seals, Duesterloh Fluidtechnik shaft seals, Duesterloh Fluidtechnik metal seals, Duesterloh Fluidtechnik high-pressure seals, Duesterloh Fluidtechnik spiral seals, Duesterloh Fluidtechnik centrifugal seals, Duesterloh Fluidtechnik sealing rings. Duesterloh Fluidtechnik original imports from Germany. Welcome customers to inquire and order.