German PAUL MESSDIENSTE sensors, PAUL MESSDIENSTE models, PAUL MESSDIENSTE prices

PAUL MESSDIENSTE sensors are components that convert changes in non-electrical quantities (such as speed and pressure) into changes in electrical quantities. Depending on the non-electrical quantity being converted, they can be classified into pressure sensors, speed sensors, temperature sensors, etc., and serve as parts and accessories for measurement and control instruments and equipment.

PAUL MESSDIENSTE sensor structure

It consists of two parts: the scale grating and the grating readhead. The figure on the right shows the structure of the grating ruler. The key part of the grating detection device is the grating readhead, which is composed of a light source, a condenser lens, an index grating, photoelectric elements, and an adjustment mechanism. There are many structural forms of grating readheads, which are classified into direct-receiving readheads (also known as silicon photovoltaic cell readheads), mirror-image readheads, beam-splitter readheads, and metal grating reflective readheads based on their structural characteristics and application scenarios.

PAUL MESSDIENSTE sensor principle

The essence of a grating displacement sensor is to measure position using the grating pitch as a standard ruler. High-resolution grating rulers are generally expensive and difficult to manufacture. To improve system resolution, Moiré fringes need to be subdivided; grating ruler sensor systems mostly use electronic subdivision methods. When two gratings overlap with a slight inclination, Moiré fringes are generated in a direction roughly perpendicular to the grating lines. As the grating moves, the Moiré fringes move up and down accordingly. This converts the measurement of the grating pitch into the measurement of the number of Moiré fringes. Within the width of one Moiré fringe, placing 4 photoelectric devices at specific intervals enables electronic subdivision and direction determination. For example, for a grating ruler with 50 line pairs per mm, the grating pitch is 0.02mm. If four-fold subdivision is used, counting pulses with a resolution of 5μm can be obtained, which achieves very high precision in general industrial measurement and control. Since displacement is a vector, both its magnitude and direction must be detected; therefore, at least two photoelectric signals with different phases are required. To eliminate common-mode interference, DC components, and even harmonics, a differential amplifier composed of low-drift operational amplifiers is typically used. The 4 photoelectric signals obtained from 4 photosensitive devices are sent to the input terminals of 2 differential amplifiers respectively. The two signals output from the differential amplifier have a phase difference of π/2. To obtain direction determination and counting pulses, these two signals must first be shaped into square waves with a duty cycle of 1:1. Then, by comparing the phases of the square waves, the movement direction of the grating ruler can be determined. By counting the square wave pulses, the displacement and speed of the grating ruler can be obtained.

PAUL MESSDIENSTE sensor usage precautions

When plugging and unplugging the connector of the linear encoder sensor and the digital readout unit, ensure the power is turned off. Install an external protective cover whenever possible, and promptly remove chips and oil splashed onto the scale to strictly prevent any foreign matter from entering the housing of the linear encoder sensor. Regularly check whether the mounting and connection screws are loose. To extend the service life of the dust-proof sealing strip, apply a thin, even layer of silicone oil to the strip, taking care not to let it splash onto the glass grating etched surface. To ensure reliable operation of the linear encoder sensor, periodically clean and wipe the linear encoder scale surface and the index grating surface with an ethanol mixture (50%), keeping the glass linear encoder scale surface clean. The linear encoder sensor must not be subjected to severe vibration or impact, as this may damage the linear encoder scale; if the scale fractures, the sensor will fail. Do not disassemble the linear encoder sensor yourself, and never arbitrarily change the relative gap between the main scale and the secondary scale. Doing so may compromise the accuracy of the sensor and cause relative friction between the main and secondary scales, damaging the chrome layer and thus the grating lines, which renders the linear encoder scale unusable. Take care to prevent oil stains and water from contaminating the linear encoder scale surface, as this can disrupt the distribution of the grating lines and cause measurement errors. Avoid operating the linear encoder sensor in environments with severe corrosive effects, to prevent corrosion of the chrome grating layer and the scale surface, which would degrade the quality of the linear encoder scale.

Weidou Intelligent Technology specializes in selling German PAUL MESSDIENSTE sensors, PAUL MESSDIENSTE proximity sensors, PAUL MESSDIENSTE distance sensors, PAUL MESSDIENSTE vision sensors, PAUL MESSDIENSTE displacement sensors, PAUL MESSDIENSTE load cells, PAUL MESSDIENSTE speed sensors, PAUL MESSDIENSTE photoelectric sensors, PAUL MESSDIENSTE position sensors, PAUL MESSDIENSTE angle sensors, PAUL MESSDIENSTE tactile sensors, PAUL MESSDIENSTE temperature sensors, PAUL MESSDIENSTE pressure sensors, PAUL MESSDIENSTE flow sensors, PAUL MESSDIENSTE level sensors, PAUL MESSDIENSTE motion sensors, and PAUL MESSDIENSTE process sensors. Original imports from Germany. Welcome inquiries and orders from users.