German FONDERIE OFFICINE sensors, FONDERIE OFFICINE models, FONDERIE OFFICINE prices

FONDERIE OFFICINE sensors precisely measure the actual displacement of the detected product by detecting the absolute position of the movable magnetic ring through internal non-contact measurement and control technology; the high precision and high reliability of these sensors have been widely applied in thousands of practical cases. Since the movable magnetic ring used for position determination does not come into direct contact with the sensitive element, the sensor can be used in extremely harsh industrial environments and is not easily affected by oil stains, solutions, dust, or other contaminants. In addition, the sensor uses high-tech materials and advanced electronic processing technology, allowing it to operate in high-temperature, high-pressure, and high-vibration environments. The sensor output signal is the absolute displacement value; even if the power is interrupted and reconnected, data will not be lost, and there is no need to re-zero. Since the sensitive element is non-contact, repeated detection will not cause any wear to the sensor, greatly improving detection reliability and service life.

FONDERIE OFFICINE sensor classification

1) Laser speed measurement: With the rise of modern precision manufacturing and the demand for cost savings, non-contact speed sensors are gradually replacing contact speed sensors. Currently, the most common and high-precision non-contact laser speed sensor on the market is the ZLS-Px aberration speed sensor. The aberration speed sensor has two ports: one emission port that emits a LED light source, and one high-speed photography port that achieves CCD area high-speed imaging comparison. By comparing images at two points in time within an extremely short period, the distance the object moves is determined, and combined with the algorithm inside the sensor, the speed of the object is output in real time. As shown in the figure, (1) is the LED light emission port, (2) is the camera reception port, (3) and (4) are terminal blocks, and (5) are fixing screw holes. The (1) LED light emission port emits laser light toward the measured object, which reflects to the (2) camera reception port. After receiving the signal, it is transmitted to the signal processor, which calculates the speed using an algorithm. The ZLS-Px aberration speed sensor can simultaneously measure speed and length in two directions. It can detect not only whether the measured body has stopped but also its direction of motion. Mount the sensor on a stable bracket to ensure that the rotating object does not produce excessive vibration during rotation, thereby allowing measurement of the rotation angle and speed of the rotating body. 2) Radar speed measurement: Traditional speed measurement mostly involves rotational motion speed measurement and linear motion speed measurement. However, there are many irregular speed measurements in real-world industrial automation, such as athlete speed measurement, traffic vehicle speed measurement, and golf ball speed measurement. Radar speed sensors can meet these requirements.

FONDERIE OFFICINE sensor principle

Transmissive speed sensors consist of a slotted or notched disk, a light source, and a phototube. When the disk rotates with the measured shaft, light can only reach the phototube through the holes or notches. When the phototube is illuminated, its reverse resistance is very low, outputting an electrical pulse signal. When the light source is blocked by the disk, the reverse resistance of the phototube is very high, and no signal is output. Thus, the rotational speed of the measured shaft can be determined based on the number of holes or notches on the disk. The usual number of disk holes or notches is unclear in the source, so the photoelectric converter outputs 60 pulse signals per revolution of the measured shaft. If the time base signal of the electronic counter is set to 1s, the rotational speed of the measured shaft can be read directly. The principle of reflective speed sensors is similar to that of transmissive sensors, converting changes in sensed light into electrical signal changes via a phototube, but they obtain pulse signals through light reflection. Typically, reflective material is attached to the measurement area of the measured shaft to form a reflective surface. Commonly used reflective materials include special speed-measuring reflective paper tape (adhesive tape); aluminum foil or other reflective materials can also be used, and sometimes white paint is applied to the measurement area as a reflective surface. The projector and reflective surface must be properly configured, typically with a distance of 5-15M between them. When the measured shaft rotates, the photoelectric element receives pulsed light and outputs corresponding electrical signals to the electronic counter, thereby measuring the rotational speed of the shaft. The waveform of the output signal from photoelectric speed sensors is relatively regular, close to a standard square wave, with almost no interference signals generated. However, vibration in transmissive types can reduce the lifespan of the light source, making them unsuitable for conditions with strong vibration. Reflective types have no mechanical connection with the measured shaft and are convenient to use.

FONDERIE OFFICINE sensor industry applications

1) Modern cars are generally equipped with engine control, autonomous driving, ABS, TRC, automatic door locking, active suspension, guidance systems, electronic instruments, and other devices, all of which require vehicle speed signals. Therefore, the accuracy and stability of the output signal from the vehicle speed sensor will greatly affect these control units. Automotive speed sensors mostly adopt a Hall-effect structure. A Hall speed sensor is a magnetoelectric sensor based on the Hall effect, characterized by high sensitivity to magnetic fields, stable output signal, high frequency response, strong anti-electromagnetic interference capability, simple structure, and ease of use. It mainly consists of permanent magnets with a specific number of pole pairs (generally 4 or 8 pairs), Hall elements, a rotating mechanism, and input/output connectors. Its working principle is that when the sensor's rotating mechanism rotates under external drive, it drives the permanent magnet to rotate, causing periodic changes in the magnetic field passing through the Hall element. This causes changes in the output voltage of the Hall element, which is processed by subsequent circuits to form a stable pulse voltage signal as the output of the speed sensor. Key electrical technical parameters of Hall-structure speed sensors include high output voltage, low output voltage, duty cycle, period, rise time, fall time, and number of pulses per cycle. To ensure product performance and reliability, these parameters must be quantitatively tested before leaving the factory. Test systems featuring integration and intelligence, efficient automatic measurement, software calculation, and graphical or tabular display of test results are increasingly favored by automotive speed sensor manufacturers. A comprehensive testing device has been developed for performance measurement of commonly used Hall-effect vehicle speed sensors. Considering cost, the high-speed counter port of a microprocessor is used for data acquisition from the vehicle speed sensor, and software control is used to calculate and graphically display the acquired data. The completed testing device offers advantages such as high testing precision, reliable data communication, a user-friendly graphical interface, strong anti-interference capability, simple and intuitive testing process, and low system development cost. It has good market promotion potential, so speed sensors will have huge application prospects in vehicle speed detection. 2) Speed sensors for belt conveyors use Hall sensors, which are sensors that utilize the Hall effect to achieve magnetoelectric conversion. The Hall effect was discovered in 1879 and has a development history of more than 100 years, but its application gained attention and widespread adoption only in the 50s of this century due to the rapid development of microelectronics, leading to the continuous development of various Hall elements. China began increasing research on Hall elements in the 20s of the 70 century. After nearly several decades of research and development, it is now possible to produce Hall elements with various performances, such as standard type, high-sensitivity type, low-temperature-coefficient type, temperature/magnetic measurement type, and switch-type Hall elements. Due to the characteristics of Hall sensors, such as high sensitivity, good linearity, high stability, small size, and high-temperature resistance, they have been widely used in various industrial fields including non-electrical quantity measurement and automatic control, computer devices, and modern military technology.

Weidou Intelligent Technology specializes in selling German FONDERIE OFFICINE sensors, FONDERIE OFFICINE proximity sensors, FONDERIE OFFICINE distance sensors, FONDERIE OFFICINE vision sensors, FONDERIE OFFICINE displacement sensors, FONDERIE OFFICINE load cells, FONDERIE OFFICINE speed sensors, FONDERIE OFFICINE photoelectric sensors, FONDERIE OFFICINE position sensors, FONDERIE OFFICINE angle sensors, FONDERIE OFFICINE tactile sensors, FONDERIE OFFICINE temperature sensors, FONDERIE OFFICINE pressure sensors, FONDERIE OFFICINE flow sensors, FONDERIE OFFICINE level sensors, FONDERIE OFFICINE motion sensors, FONDERIE OFFICINE process sensors. Original imports from Germany. Welcome inquiries and orders from users.