German end pump end model end price

end pumps are also called positive displacement devices. Like a piston in a cylinder, when one gear tooth enters the fluid space of another, the liquid and the tooth cannot occupy the same space simultaneously because liquids are incompressible. Thus, the liquid is mechanically squeezed out. Due to the continuous meshing of the teeth, this phenomenon occurs continuously, providing a continuous discharge volume at the pump outlet. The discharged volume is the same for each revolution of the pump. As the drive shaft rotates continuously, the pump discharges fluid without interruption. The pump flow rate is directly related to the pump speed.

end pump operating principle

The concept of a gear pump is very simple. Its most basic form consists of two gears of identical size meshing and rotating within a closely fitted housing. The interior of this housing resembles an "8" shape, with the two gears installed inside. The outer diameter of the gears and their sides fit closely with the housing. Material from the extruder enters the space between the two gears at the suction inlet and fills this space. It moves along the housing as the teeth rotate and is finally discharged when the two teeth mesh. Gear pumps are also called positive displacement devices. Like a piston in a cylinder, when one gear tooth enters the fluid space of another, the liquid and the tooth cannot occupy the same space simultaneously because liquids are incompressible. Thus, the liquid is mechanically squeezed out. Due to the continuous meshing of the teeth, this phenomenon occurs continuously, providing a continuous discharge volume at the pump outlet. The discharged volume is the same for each revolution of the pump. As the drive shaft rotates continuously, the pump discharges fluid without interruption. The pump flow rate is directly related to the pump speed. In practice, there is a small amount of fluid loss within the pump because this fluid is used to lubricate the bearings and the sides of the gears. Furthermore, the pump body cannot have a gap-free fit, so it is impossible for the fluid to be discharged 100% from the outlet. Therefore, a small amount of fluid loss is inevitable, preventing the pump's operating efficiency from reaching 100%. However, the pump can still operate well, achieving efficiencies of 93% to 98% for most extruded materials. This type of pump is not significantly affected by changes in fluid viscosity or density during the process. If there is a damper, such as a filter screen or restrictor at the discharge side, the pump will push the fluid through them. If this damper changes during operation—i.e., if the filter becomes dirty or clogged, or if the back pressure of the restrictor increases—the pump will maintain a constant flow until the mechanical limit of the weakest component in the system is reached (a torque limiter is usually installed). The rotational speed of a pump is actually limited, primarily depending on the process fluid. If oil is being conveyed, the pump can rotate at high speeds, but this limit increases significantly when the fluid is a high-viscosity polymer melt. It is crucial to fill the space between the two teeth on the suction inlet side with high-viscosity fluid. If this space is not completely filled, the pump cannot discharge an accurate flow rate. Therefore, the PV value (pressure × flow velocity) is another limiting factor and a process variable. Due to these limitations, gear pump manufacturers offer a range of products with different specifications and displacements (volume discharged per revolution). These pumps are matched to specific application processes to optimize system capacity and price.

end pump usage precautions

Gear pumps are suitable for various industries and handle a wide range of media. These gear pumps offer advantages such as robust construction, easy installation, easy disassembly, simple maintenance, uniform and continuous flow, slight wear, and long service life. 1) During the use of gear pumps, frequent greasing is required. Since lubricating grease evaporates relatively easily, attention must be paid to replenishment and replacement. Additionally, keep the bearing area clean. 2) When using or after using the electric oil pump, place it in a relatively dry, non-corrosive, and clean environment. 3) Frequently inspect and maintain the gear pump during use. Check the electric oil drum, including the power cord, internal wiring, plug, and switch, to ensure they are functioning normally. Inspect bearing components for any damage. 4) Preserve every component of the gear pump. During disassembly and inspection, keep all parts clean and stored properly.

end pump maintenance

When using a gear pump, wear on the gear pump is unavoidable, which leads to many problems. Therefore, it is necessary to learn the most common maintenance techniques for gear pumps. This enables accurate diagnosis when issues arise. Routine maintenance procedures are as follows: 1) Maintenance of the working surface: If the wear on the pump cover's working surface is minimal, the wear marks can be removed by manual lapping, by placing a small amount of valve grinding compound on a surface plate or thick glass plate, then placing the pump cover on top and lapping it, until the wear marks are removed and the working surface is flat. If the wear depth on the working surface of the pump cover exceeds zero point one millimeter, machining followed by lapping must be performed for repair. 2) Maintenance of the drive shaft bushing bore: The repair method for wear on the drive shaft bushing bore in the pump cover is the same as that for the housing's drive shaft bushing bore. Repair of the pump housing bore: After wear occurs in the pump housing bore, it is repaired using the sleeve insertion method, which involves boring out the bore and fitting a cast iron or steel sleeve. After inserting the sleeve, bore the inner cavity to the required dimensions, and grind down the sleeve protruding from the end face to make it flush with the pump housing mating surface. 3) Maintenance of the valve seat: Pressure-limiting valves come in two types: ball valves and plunger valves. After the ball valve seat wears, place a steel ball on the valve seat, then gently tap the steel ball with a metal rod, until the ball valve seats tightly against the valve seat. If the valve seat is severely worn, ream to remove the wear marks, and then use the above method to achieve a tight seal. After the plunger-type valve seat wears, add a small amount of valve grinding compound for lapping, lap until a tight seal is achieved. The above describes some basic maintenance of components for gear pumps. During application, other different problems may also be encountered. These different problems must be carefully analyzed to identify their causes.

Weidou Intelligent Technology specializes in selling German end gear pumps, end gear pumps, end diaphragm pumps, end centrifugal pumps, end piston pumps, end vacuum pumps, end screw pumps, end submersible pumps, end peristaltic pumps, end lubrication pumps, end vane pumps, end metering pumps, end hand pumps, end barrel pumps, end cam pumps, end booster pumps, end liquid pumps, and end air pumps. Original imports from Germany. Customers are welcome to inquire and order.