German jakob keller valves, jakob keller models, jakob keller prices

The closure member of the jakob keller valve is a plug-shaped disc. The sealing surface is flat or conical. The disc moves linearly along the centerline of the valve seat. The stem movement type (common name: rising stem) also includes lift-and-rotate stem types. It can be used to control the flow of various fluids such as air, water, steam, various corrosive media, slurry, oil products, liquid metals, and radioactive media. Therefore, this type of shut-off stop valve is very suitable for isolation, regulation, and throttling. Since the opening or closing stroke of the valve stem of this type of valve is relatively short, and it has a very reliable shut-off function, and since the change in the valve seat port is directly proportional to the disc stroke, it is very suitable for flow regulation.

jakob keller valve stop valve features

Compared with another commonly used shut-off valve in industrial production, the gate valve, the stop valve has a simpler structure, making it easier to manufacture and maintain. In terms of service life, the sealing surface of the stop valve is not easily worn or scratched. During the opening and closing process, there is no relative sliding between the disc and the seat sealing surface, resulting in less wear and scratching on the sealing surface, thus extending the service life of the sealing pair. The disc stroke of the stop valve during full opening and closing is small, and its height is relatively smaller than that of the gate valve. The disadvantage of the stop valve is that the opening and closing torque is large, making it difficult to achieve rapid opening and closing. Because the flow channel inside the valve body is relatively tortuous, the fluid flow resistance is high, causing significant loss of fluid power in the pipeline.

Precautions for jakob keller valve performance testing

1) When valves of a specific specification are manufactured in batches, an official agency should be commissioned to perform the following performance tests: (1) Opening and closing torque of the valve under working pressure conditions; (2) Testing of the flow resistance coefficient of the valve under pipeline water transmission conditions. 2) The following tests should be performed on the valve before leaving the factory: (1) With the valve in the open position, the valve body shall withstand an internal pressure test at twice the valve working pressure; (2) With the valve in the closed position, both sides shall separately withstand 11 times the valve working pressure without leakage; however, for metal-sealed butterfly valves, the leakage value shall not exceed the relevant requirements.

jakob keller valve operation

For stop valves, one must know not only how to install and maintain them but also how to operate them. When opening or closing a stop valve, apply force steadily; do not impact. Certain high-pressure stop valves designed for impact opening and closing have components that account for this impact force and cannot be equated with general stop valves. When the stop valve is fully open, turn the handwheel back slightly to tighten the threads and prevent loosening and damage. When the pipeline is first used, there may be a lot of dirt inside. You can slightly open the stop valve and use the high-speed flow of the medium to flush it away, then close it gently (do not close quickly or forcefully to prevent residual impurities from damaging the sealing surface), then open it again. Repeat this multiple times to flush out the dirt before putting it into normal operation. For normally open stop valves, dirt may adhere to the sealing surface. When closing, use the above method to flush it clean, then close it tightly. If the handwheel or handle is damaged or lost, replace it immediately. Do not use an adjustable wrench as a substitute to avoid damaging the square section of the valve stem, which could lead to ineffective opening/closing and cause accidents in production. For certain media, cooling after the stop valve is closed causes valve components to contract. Operators should close it again at an appropriate time to ensure no fine gaps remain on the sealing surface. Otherwise, the medium flowing through the fine gaps at high speed can easily erode the sealing surface. During operation, if the operation feels too strenuous, analyze the cause. If the packing is too tight, loosen it appropriately. If the valve stem is skewed, notify personnel for repair. Some stop valves experience difficulty in opening when the closure member expands due to heat in the closed state. If opening is necessary at this time, loosen the valve cover threads by half to one turn to relieve valve stem stress, then turn the handwheel.

Weidou Intelligent Technology specializes in selling German jakob keller valves, jakob keller safety valves, jakob keller stop valves, jakob keller control valves, jakob keller solenoid valves, jakob keller ball valves, jakob keller proportional valves, jakob keller diaphragm valves, jakob keller butterfly valves, jakob keller hydraulic actuated valves, jakob keller check valves, jakob keller pressure reducing valves, jakob keller relief valves, jakob keller sequence valves, jakob keller balance valves, jakob keller throttle valves, jakob keller directional control valves. Original German imports. Welcome inquiries and orders from users.