German SIEMENS bearings SIEMENS models SIEMENS prices

SIEMENS bearings can simultaneously withstand radial and axial loads. They can operate at higher speeds. The greater the contact angle, the higher the axial load capacity. The contact angle is the angle between the line connecting the contact points of the ball and raceway in the radial plane and the perpendicular to the bearing axis. High-precision and high-speed bearings typically use a 15 degree contact angle. Under axial force, the contact angle increases.

SIEMENS bearing introduction

Self-aligning ball bearings are bearings with spherical balls assembled between an inner ring with two raceways and an outer ring with a spherical raceway. The center of curvature of the outer ring raceway surface aligns with the bearing center, so they have the same self-aligning function as automatic self-aligning ball bearings. When the shaft or housing deflects, they can automatically adjust without increasing the bearing load. Spherical roller bearings can withstand radial loads and axial loads in both directions. They have high radial load capacity and are suitable for heavy load and shock load conditions. Bearings with a tapered bore in the inner ring can be mounted directly, or installed on a cylindrical shaft using a locking assembly or withdrawal sleeve. Cages include stamped steel cages, molded polyamide cages, and machined copper alloy cages. Self-aligning ball bearings come in cylindrical bore and tapered bore structures. Cage materials include steel sheet and synthetic resin. Their characteristic is that the outer ring raceway is spherical, providing automatic self-alignment to compensate for errors caused by misalignment and shaft deflection. However, the relative inclination between the inner and outer rings must not exceed 3 degrees. They can withstand large radial loads and certain axial loads. Since the outer ring raceway is spherical, these bearings have self-aligning performance. When the shaft bends or tilts due to force, causing the relative inclination between the inner ring centerline and outer ring centerline to not exceed 1°～2.5°, the bearing can still operate. Self-aligning ball bearings have cylindrical and tapered bores. The taper of the tapered bore is 1：1 2 or 1：30. To enhance lubrication performance, annular oil grooves and three oil holes are machined into the outer ring.

SIEMENS bearing features and structure

Primarily withstands radial loads, while also capable of withstanding smaller axial loads. Axial displacement of the shaft (housing) is limited within the clearance limit. It has automatic self-aligning performance, allowing normal operation under conditions of small relative inclination between the inner and outer rings. It is suitable for components where the support housing bore cannot strictly guarantee coaxiality. Structural forms: Self-aligning ball bearings with dust covers and seals are filled with an appropriate amount of grease during assembly. They should not be heated or cleaned before installation, and no further lubrication is required during use. They are suitable for operating temperatures between － 30 ℃ and + 120 ℃. Main applications of self-aligning ball bearings: Suitable for precision instruments, low-noise motors, automobiles, motorcycles, and general machinery. They are the most widely used type of bearing in the mechanical industry.

SIEMENS bearing sealing

Bearing seals can be divided into two categories: integral seals and external seals. Integral bearing seals refer to bearings manufactured with built-in sealing devices, such as dust covers and sealing rings. This type of seal occupies minimal space, is easy to install and remove, and has a relatively low cost. External bearing sealing devices are sealing assemblies with various performance characteristics manufactured within components such as end caps. External bearing seals are further classified into non-contact seals and contact seals. Non-contact seals are suitable for high-speed and high-temperature applications and come in different structural forms, including clearance types, labyrinth types, and gasket types. Contact seals are suitable for medium and low-speed operating conditions, with common structural forms including felt seals and leather cup seals. In engineering design, various seal types are often comprehensively applied to achieve better sealing performance, depending on the bearing's operating conditions and environmental requirements for sealing. The selection of external bearing seals should consider the following main factors: bearing lubricant type (grease and oil); bearing operating environment and space constraints; advantages of the shaft support structure and allowable angular misalignment; circumferential speed of the sealing surface; bearing operating temperature; and manufacturing cost.

Weidou Intelligent Technology professionally sells German SIEMENS plain bearings, SIEMENS rolling bearings, SIEMENS spherical plain bearings, SIEMENS deep groove ball bearings, SIEMENS angular contact ball bearings, SIEMENS self-aligning ball bearings, SIEMENS thrust ball bearings, SIEMENS double-direction thrust angular contact ball bearings, SIEMENS combination bearings, SIEMENS thrust roller bearings, SIEMENS needle roller bearings, SIEMENS insert ball bearings, SIEMENS spherical roller bearings, SIEMENS flanged bearings, SIEMENS linear bearings, SIEMENS original German imports. Welcome customers to inquire and order.