German inkoma coupling inkoma model inkoma price

inkoma coupling is a widely used coupling, also known as a jaw coupling, consisting of two metal jaw disks and an elastomer. The two metal jaw disks are generally made of 45 steel, but aluminum alloy is also used when load sensitivity is required.

inkoma coupling structure

It consists of two shaft hubs and a center slider. The center slider, acting as a torque transmission element, is usually made of engineering plastic; in special cases, other materials such as metals can be selected. The center slider is connected to the shaft hubs on both sides via slots distributed at 90° relative positions, thereby achieving torque transmission. A slight pressure fit between the center slider and the shaft hubs allows the coupling to operate with zero backlash during equipment operation. Over time, the slider may lose its backlash-free function due to wear, but the center slider is inexpensive and easy to replace, restoring original performance after replacement. Slider couplings are commonly used with general-purpose motors and, in individual cases, to connect servo motors, correcting relative displacement through the sliding of the center slider during use. Since the half-coupling and the intermediate disk form a sliding pair and cannot rotate relative to each other, the angular velocity of the driving shaft and the driven shaft must be equal. However, when operating with relative displacement between the two shafts, the intermediate disk generates significant centrifugal force, increasing dynamic loads and wear. Therefore, care should be taken during selection to ensure the operating speed does not exceed the specified value. This type of coupling is generally used for speeds n<250r/min, where shaft stiffness is high and there are no severe impacts.

inkoma coupling features

The material for slider coupling parts can be 45 steel, with heat treatment required on the working surfaces to increase hardness; for lower requirements, Q275 steel can be used without heat treatment. To reduce friction and wear, oil should be injected through the oil hole in the intermediate disk for lubrication during use. Since the half-coupling and the intermediate disk form a sliding pair and cannot rotate relative to each other, the angular velocity of the driving shaft and the driven shaft must be equal. However, when operating with relative displacement between the two shafts, the intermediate disk generates significant centrifugal force, increasing dynamic loads and wear. Therefore, care should be taken during selection to ensure the operating speed does not exceed the specified value. This type of coupling is generally used for speeds n<250r/min, where shaft stiffness is high and there are no severe impacts. A slight pressure fit between the center slider and the shaft hubs allows the coupling to operate with zero backlash during equipment operation. Over time, the slider may lose its backlash-free function due to wear, but the center slider is inexpensive and easy to replace, restoring original performance after replacement. Slider couplings are commonly used with general-purpose motors and, in individual cases, to connect servo motors, correcting relative displacement through the sliding of the center slider during use. Since resistance to relative displacement comes from the friction between the slider and the shaft hubs, the bearing load between them does not increase with greater relative displacement. Slider couplings can eliminate additional loads between shafts during automatic motor control. The fixed body uses internal splines for sliding, while the sliding body's inner and outer sleeves can slide relatively in the axial direction. This coupling integrates sliding and rotation. For equivalent rotational diameters, its shortest dimension is far smaller than that of a cross-axis coupling. It improves the uniformity of load distribution on the working surface and can transmit higher torque, though elasticity is slightly reduced.

inkoma coupling applications

Unlike other couplings, the slider coupling has no elastic elements that work like springs, so bearing loads do not increase with greater relative displacement between shafts. Regardless, this series of couplings offers good value for money, with the ability to choose sliders of different materials being its greatest advantage. Juren Company can provide a variety of raw material options for center sliders to suit different applications based on specific customer requirements. Generally, one type of material is suitable for zero-backlash, high-torque rigidity, and high-torque conditions, while another type is suitable for low-precision positioning, where zero-backlash is not required, but vibration absorption and noise reduction functions are needed. Non-metallic sliders also provide excellent electrical insulation and can serve as mechanical fuses. When the engineering plastic slider is damaged, torque transmission is completely terminated, thereby protecting valuable mechanical parts. This design is suitable for large parallel relative displacements. The three-part design of the slider coupling limits its ability to compensate for axial deviations, making it unsuitable for push-pull applications. Additionally, since the center slider is floating, the motion of the two shafts must ensure that the slider does not disengage.

Weidou Intelligent Technology specializes in selling German inkoma rigid couplings, inkoma flexible couplings, inkoma safety couplings, inkoma universal joints, inkoma diaphragm couplings, inkoma jaw couplings, inkoma flange couplings, inkoma cross-slide couplings, inkoma slider couplings, inkoma gear couplings, inkoma tire couplings, inkoma elastic couplings, inkoma bellows couplings, inkoma roller chain couplings, inkoma spring couplings, inkoma original German imports. Welcome inquiries and orders from users.