German MEZ BRNO pump, MEZ BRNO model, MEZ BRNO price

MEZ BRNO pumps are also known as positive displacement devices. Like a piston in a cylinder, when a tooth enters the fluid space of another tooth, the liquid and the tooth cannot occupy the same space at the same time because liquids are incompressible. Thus, the liquid is mechanically squeezed out. Due to the continuous meshing of the teeth, this phenomenon occurs continuously, providing a continuous discharge volume at the pump outlet. The discharged volume is the same for each revolution of the pump. As the drive shaft rotates continuously, the pump discharges fluid without interruption. The pump flow rate is directly related to the pump speed.

MEZ BRNO pump operating principle

The concept of a gear pump is very simple. Its most basic form consists of two gears of the same size meshing and rotating within a closely fitted housing. The interior of this housing resembles an "8" shape, with the two gears installed inside. The outer diameter of the gears and their sides fit closely with the housing. Material from the extruder enters between the two gears at the suction inlet and fills this space. It moves along the housing as the teeth rotate and is finally discharged when the two teeth mesh. Gear pumps are also known as positive displacement devices. Like a piston in a cylinder, when a tooth enters the fluid space of another tooth, the liquid and the tooth cannot occupy the same space at the same time because liquids are incompressible. Thus, the liquid is mechanically squeezed out. Due to the continuous meshing of the teeth, this phenomenon occurs continuously, providing a continuous discharge volume at the pump outlet. The discharged volume is the same for each revolution of the pump. As the drive shaft rotates continuously, the pump discharges fluid without interruption. The pump flow rate is directly related to the pump speed. In practice, there is a small amount of fluid loss within the pump because this fluid is used to lubricate the bearings and the sides of the gears. Furthermore, the pump body cannot have a gap-free fit, so the fluid cannot be discharged 100% from the outlet. Therefore, a small amount of fluid loss is inevitable, preventing the pump's operating efficiency from reaching 100%. However, the pump can still operate well, achieving an efficiency of 93% to 98% for most extruded materials. This type of pump is not significantly affected by changes in fluid viscosity or density during the process. If there is a damper, such as a filter screen or restrictor on the discharge side, the pump will push the fluid through them. If this damper changes during operation—i.e., if the filter becomes dirty or clogged, or if the back pressure of the restrictor increases—the pump will maintain a constant flow until the mechanical limit of the weakest component in the device is reached (a torque limiter is usually installed). The rotational speed of a pump is actually limited, primarily depending on the process fluid. If oil is being transported, the pump can rotate at high speeds, but this limit increases significantly when the fluid is a high-viscosity polymer melt. It is crucial to fill the space between the two teeth on the suction inlet side with high-viscosity fluid. If this space is not completely filled, the pump cannot discharge an accurate flow rate. Therefore, the PV value (pressure × flow velocity) is another limiting factor and a process variable. Due to these limitations, gear pump manufacturers offer a range of products with different specifications and displacements (volume discharged per revolution). These pumps are matched to specific application processes to optimize system capacity and cost.

MEZ BRNO pump usage precautions

Gear pumps are suitable for various industries and handle a wide range of media. These gear pumps offer advantages such as robust construction, easy installation, easy disassembly, simple maintenance, uniform and continuous flow, minimal wear, and long service life. 1) During the use of gear pumps, frequent greasing is required. Since grease evaporates relatively easily, attention must be paid to replenishment and replacement. Additionally, keep the bearing area clean. 2) When using or after use, place the electric oil pump in a dry, non-corrosive, and clean environment. 3) Frequently inspect and maintain the gear pump during use. Check the electric oil drum, including the power cord, internal wiring, plug, and switch, to ensure they are functioning normally. Inspect bearing components for any damage. 4) Preserve every component of the gear pump. During disassembly and inspection, keep all parts clean and stored properly.

MEZ BRNO pump maintenance

When using a gear pump, it is inevitable to encounter wear of the gear pump, therefore many problems will arise, so it is necessary to learn the most common maintenance technique for gear pumps. This enables accurate diagnosis when problems occur. Routine maintenance techniques are as follows: 1) Maintenance of the working surface: If the wear on the pump cover working surface is relatively small, you can manually use a lapping method to remove the wear marks, that is, place a small amount of valve grinding compound on a flat platform or thick glass plate, then place the pump cover on top and perform lapping, until the wear marks are ground away, and the working surface is flat. If the wear depth on the working surface of the pump cover exceeds zero point one millimeter, turning followed by lapping must be used for repair. 2) Maintenance of the drive shaft bushing bore: The repair method for wear of the drive shaft bushing bore on the pump cover is the same as that for wear of the drive shaft bushing bore in the housing. Repair of the pump housing bore: After wear occurs in the pump housing bore, the bore lining method is always adopted for repair, which involves boring out the inner bore and fitting a cast iron or steel bushing. After inserting the bushing, bore the inner cavity to the required dimensions, and grind off the portion of the bushing protruding from the end face, so that it is flush with the pump housing mating surface. 3) Maintenance of the valve seat: Pressure-limiting valves come in two types: ball valves and plunger valves. After the ball valve seat wears, a steel ball can be placed on the valve seat, and then the steel ball is gently tapped with a metal rod, until the ball valve seats tightly against the valve seat. If the valve seat is severely worn, ream to remove the wear marks, and then use the above method to achieve a tight seal. After the plunger-type valve seat wears out, a small amount of valve grinding compound can be added for lapping, lapping until a tight seal is achieved. The above describes some basic maintenance procedures for components of gear pumps. During application, other different issues may also arise. These different issues must be carefully analyzed to identify their root causes.

Weidou Intelligent Technology specializes in selling German MEZ BRNO gear pumps, MEZ BRNO gear pumps, MEZ BRNO diaphragm pumps, MEZ BRNO centrifugal pumps, MEZ BRNO piston pumps, MEZ BRNO vacuum pumps, MEZ BRNO screw pumps, MEZ BRNO submersible pumps, MEZ BRNO peristaltic pumps, MEZ BRNO lubrication pumps, MEZ BRNO vane pumps, MEZ BRNO metering pumps, MEZ BRNO hand pumps, MEZ BRNO barrel pumps, MEZ BRNO cam pumps, MEZ BRNO booster pumps, MEZ BRNO liquid pumps, and MEZ BRNO air pumps. All are original imports from Germany. Customers are welcome to inquire and order.