Goudsmit designs and manufactures high-quality Magnetic magnets, including Goudsmit metal separation magnets for various industries, Goudsmit recycling magnets, Goudsmit metal processing magnets, Goudsmit transport magnets, Goudsmit lifting magnets, and Goudsmit holding and demagnetizing components.

TPGC040088 Magnet Performance Introduction:

Magnet Part Number TPGC040088

Description of friction type - #40 mm  -  140 N.

Product Key HGR-SQ-040-FP-R-M-S

TPGC040088 MagnetDelivery time: (if not in stock) 4-6 weeks

TPGC040088 MagnetSpecific applications x

Switching "Pneumatic: 2 compressed air connections or:

1 vacuum connection: see 'Gripper Connections for Vacuum Control' (Documents tab)"

Includes vulcanized friction pads to provide additional grip and product protection

Recommended working load：47 N (under ideal conditions - safety factor 3 according to EN13155)

TPGC040088 Magnet*Maximum tear-off force：140 N (under ideal conditions - Chart: see Documents tab - Factors affecting lifting capacity: see Lifting Magnets)

TPGC040088 Magnet*Minimum recommended plate thickness：2 mm

Interface/Connection dim. "Threaded holes M5 (4x)"

Threaded hole M8"

Pneumatic connection: M5 (2x)

Material friction pad/ring NBR 60°Shore A.

Material housing "Aluminum"

AISI316L (SS 1.4404) (Spiral cover)"

Surface treatment/finishing: anodizing

TPGC040088 MagnetColor: red

Min./max. Ambient temperature 0 to 70°C

Switching pressure "4 bar (recommended), 6 bar (max)"

Vacuum pressure -0.3 bar (on)"

Air consumption 0.040 liters/cycle (1 times up, 1 times down)

Magnetic system with 4 permanent magnetic poles

TPGC040088Magnet mass：Neodymium GSN-45, Br 13, 700 Gauss (20°C), Tmax. At 80°C

Depth 46 mm

Width 46 mm

Height 63 mm

TPGC040088 MagnetWeight 0.23 kg

TPGC040088 magnet applications:

1).TPGC040088 MagnetWhen handling thin sheets (≤1mm), the "peeling effect" must be considered. This reduces the separation force. In this case, use one or two large magnets in combination with a structure featuring multiple smaller magnets (e.g., 40×40mm).

2). When Goudsmit magnets contact paper, the paper may be damaged. In this case, select the version with polyurethane protective caps (Goudsmit friction type).

3). When using oiled paper or with high acceleration of the robotic arm, the paper can shift. This can also be prevented by using types with Goudsmit polyurethane friction pads.

4). Sometimes sheet surfaces are uneven, in which case vacuum grippers do not work; then Goudsmit magnets are an ideal solution. The larger the contact area, the better, but Goudsmit magnets always work (on ferromagnetic steel), even if circular.

5). Another situation where vacuum does not work is with perforated sheets. This poses no problem for Goudsmit magnets. Ensure the selected gripper size is larger than the holes and thoroughly test the chosen solution.

6). For small workpieces, Goudsmit offers very small magnets in its product range with low mounting height, providing additional holding strength. For example, select the HGR-RO-020 type.

7). For thin sheets (≤4mm) and oily sheets sticking together, robots sometimes pick up several sheets at once. Paper separators prevent this. These are available for both Goudsmit permanent and pneumatically switchable versions.

TPGC040088 magnet operation

TPGC040088 magnets are switched pneumatically. This moves the magnetic field to turn it on and off. Control is possible via 53 or even 52 valves.

Even in the event of a loss of air pressure or power supply, an activated Goudsmit magnet will not release.